background image

 

 

VIVOTEK

 

User's Manual - 39  

Configuration

Click 

Configuration

 on the main page to enter the camera setting pages. Note that only 

Administrators can access the configuration page. 

VIVOTEK provides an easy-to-use user interface that helps you set up your network camera 

with minimal effort. In order to simplify the user interface, detailed information will be hidden 

unless you click on the function item. When you click on the first sub-item, the detailed 

information for the first sub-item will be displayed; when you click on the second sub-item, the 

detailed information for the second sub-item will be displayed and that of the first sub-item will 

be hidden. 

The following is the interface of the main page:

Configuration List

Firmware Version

Navigation Area

Each function on the configuration list will be explained in the following sections. 

The Navigation Area provides access to all different views from the 

Home

 page (for live viewing), 

Configuration

 page, and multi-language selection.

Summary of Contents for IB8367A






































































































































































































































































































































Reviews: