Vivotek IB8367A User Manual Download

Page: 56 / 325

VIVOTEK

56 - User's Manual

■ Schedule mode

The Network Camera switches between day mode and night mode based on a specified

schedule. Enter the start and end time for the day mode. Note that the time format is [hh:mm]

and is expressed in 24-hour clock time. By default, the start and end time of day mode are set to

07:00 and 18:00.

Light sensor sensitivity

Tune the responsiveness of the IR filter to lighting conditions as Low, Normal, or High.

When completed with the settings on this page, click

Save

to enable the settings.

Summary of Contents for IB8367A






































































































































































































































































































































Search results

Summary of Contents for IB8367A

Reviews:

Related manuals for IB8367A

Brands by name

Popular brands

Vivotek IB8367A, User Manual

Search results

Summary of Contents for IB8367A

Reviews:

Related manuals for IB8367A

Brands by name

Popular brands