manualshive.com logo in svg

Vivax Metrotech VM-810, User Handbook Manual, Page: 25 / 39

Share
Download
Vivax Metrotech VM-810 User Handbook Manual Download Page 25

5     Operation

5.6     Conductor Identification using a Second Signal Clamp

When exposed, multiple conductors are present, for example in conduits or ducts, use 

the method described below to identify a specific conductor.

1.  Plug the receiver signal clamp cable into the jack on the back of the Receiver.

2.  Plug the transmitter signal clamp into the transmitter and place it around the start 

of the cable to be identified.

3.  Turn the Transmitter ON.

4.  Place the signal clamp around each conductor in succession, making sure that the 

jaws are fully closed. The conductor with the highest field strength reading is most 

likely to be the target conductor.

NOTE

The method will work only if there is no cross bonding on 

the length of the conductor between the conductor and the 

Receiver.

The Receiver signal clamp is a useful tool to help identify 

cables. However, it should not be used as positive identification 

before an unused cable is cut. Always follow company 

procedures when cutting disused or isolated cables.

5.7     Marking the Conductor

The following color markings have been established by the American Public Works 

Association (APWA):

Conductor

Color

Electric power lines, cables, or conduits

Red

Communication lines, cables, or conduits

Orange

Gas, oil, petroleum, or other gaseous materials

Yellow

Storm and sanitary sewers; drain lines

Green

Water, irrigation, or slurry lines

Blue

NOTE

If you have any questions regarding marking requirements or 

procedures, please call your local One Call Center.

Page 22 of 35

™

Summary of Contents for VM-810








































Reviews:

No comments