HOW TO USE YOUR TRAVEL IRON / STEAMER
Before first use
1. Before using, always remove the Detachable Lint Remover and check if
the voltage rating on the appliance corresponds to the mains voltage in
your home or hotel. Replace the Lint Remover back to original position.
2. Some parts of the appliance have been slightly greased and as a result the
unit may smoke slightly when switched on for the first time. After a
short while, however, this will cease.
3. Normal tap water can usually be used. But if you live in a hard water area,
we recommend you to use distilled water to insure optimum
performance of your travel iron / steamer.
HOW TO USE YOUR TRAVEL IRON / STEAMER
Controlling the Temperature
Please turn your temperature control knob to the position you desired
according to the following fabric indications by pointing to the symbol ( ) :
Ironing Tips
1. Sort the articles to be ironed according to the fabric. Ironing instruction are
usually stitched onto an inside seam of the garment and these should be
followed at all the times. Start your ironing with the fabrics requiring
the lowest heat setting.
2. If you are unsure of the fiber content of a garment, test a small areas (a
seam or inside hem) before ironing.
When in doubt, start with low heat. If wrinkles remain, gradually increase
heat to find the best setting for good results without damaging the
fabric.
HOW TO USE YOUR TRAVEL IRON
Using as Burst Steam Iron
1. Unwrap the cord. Fill the iron with water. (Refer how to fill water)
2. Plug the unit into a wall outlet. Set the temperature control knob to the
steam position (High Temperature). Then LED light will illuminate.
3. When the LED light goes out, it means the iron reached the working
temperature. The LED light will come on and goes out regularly during
ironing to indicate that the temperature control is working properly.
4. The set can be used as Steam Iron by press the Burst Button. Burst
Steaming will start. (When you first time or after some period to use Iron,
make sure to press the Burst Steam Button for 2-3 times to initiate steam.)
If you stop to press the Burst button then Steam stops. Iron can
be operating only in Horizontal position.
5. Stand the iron on Heat Rest when rearranging clothing and while not in
use.
Using as Dry Iron
This iron can also be used without steam as a dry iron even there is water
inside the water tank.
1. Unwrap the cord. Plug the unit into a wall outlet. Set the temperature
control knob to the desired position.
2. The LED light will illuminate. When the LED light goes out, it means the
iron reached the working temperature. You can start to use your Dry iron.
Make sure do not press the Steam Button.
Stand the iron on Heat Rest when rearranging clothing and while not in
use.
HOW TO USE YOUR STEAMER
WARNING : Before removing or attaching any accessories, unplug the
steamer from the electrical outlet and let it cool. .
(A)Detachable Lint Remover
(B)Detachable Clothes Brush
P/3
P/4
Filling with water
1. Lift handle into position. Gently press the water tank
released button which located at the end of water tank
and remove detachable handle cover / water tank.
2. Lift up the tank cover. Pour tap water or use the
supplied measuring cup to pour water into tank.
Do not overfill. To close the tank cover, press it down
firmly then replace water tank back to the original
position until you hear “click” sound.
• Synthetics
Synthétiques
Chemiefasern
•• Silk / Wool
Soie / Laine
Seide / Wolle
••• Linen / Cotton
Toile / Coton
Leinen / Baumwolle
1. Press down the tab to detach the lint remover.
2. Insert the tab of the lint remover into the slot on
the back side of the appliance, then press down
until it clicks into position. To use in the reverse
the direction, insert the lint remover in the
1. Unpack the detachable clothes brush package,
attached the brush by sliding it down into place
from the top, so that it locks into proper position.
2. Snap the brush out by pushing it up from the
bottom.