5
ENGLISH
USING THE WHISK
Use the whisk attachment (10) only to beat
cream, make biscuit dough or for mixing ready
desserts.
WARNING: Before assembling make sure
that the power plug is not inserted into the
mains socket.
•
Insert the whisk (10) into the gear (9).
•
Insert the whisk gear (9) into the motor unit
(2), and turn it counterclockwise until bump-
ing.
•
Insert the power plug into the mains socket.
•
Immerse the whisk (10) into the bowl with
products.
•
To switch the unit on, press and hold down
the button (4) «I». Use this operation mode for
mixing liquid products.
•
If you press and hold down the button (3)
«II», the unit will operate at maximum rota-
tion speed.
•
After you finish using the unit, take the power
plug out of the socket, disconnect the whisk
(10) from the gear (9) and disconnect the
gear (9) from the motor unit (2) by turning it
clockwise.
Attention!
•
Do not use the whisk (10) to knead stiff
dough.
•
Products should be put into the bowl
before the unit is switched on.
Using the mini-chopper
The chopper is used to chop meat, cheese,
onion, herbs, walnuts, almond, vegetables and
fruit.
Attention!
Do not chop very hard products, such as nut-
megs, coffee beans, cereals and ice.
Before you start chopping:
•
cut meat, cheese, onions, vegetables and fruit
into cubes approximately 2x2 cm in size;
•
remove stems of herbs, shell nuts;
•
remove bones, sinews and cartilage from
meat.
•
To achieve the best results, refer to the table
below:
Product
type
Weight,
g.
Approximate
processing
time, seconds
Carrots
200
30
Garlic
100
30
Bread
(rusks)
100
30
Cheese
200
30
Eggs
150
30
Meat
(lean)
200
30
Beef
200
30
Chopping
Caution! The blades of the chopping knife
are very sharp! Always hold the chopping
knife by the plastic end.
•
Place the chopper bowl (6) on a flat stable
surface.
•
Set the chopping knife (7) on the axis of
chopper bowl (6).
•
Put the food into the chopper bowl (6).
Note:
- Do not switch the unit on when the chopper
bowl (6) is empty.
•
Install the geared lid (8) on the chopper
bowl (6).
•
Install the motor unit (2) on the geared lid (8)
and turn it clockwise until it is fixed.
•
To connect the unit to the mains, insert the
power cord plug into the mains socket.
•
To switch the unit on, press and hold down
the button (4) «I».
•
When the button (3) «II» is pressed, the knife
rotates at maximal rotation speed.
•
During operation hold the motor unit (2) with
one hand and the chopper bowl (6) with the
other hand.
•
After using the unit, wait until the chopping
knife (7) fully stops.
•
Unplug the unit.
•
After using the chopper, disconnect the
motor unit (2) from the geared lid (8).
•
Remove the geared lid (8).
•
Carefully remove the chopping knife (7) tak-
ing it by the plastic end.
•
Take the chopped products out of the chop-
per bowl (6).
Attention!
Strictly follow the described sequence of
operations.
CLEANING
Attention! The blades of the chopping knife
(7) are very sharp and dangerous. Handle
VT-3413.indd 5
26.11.2014 10:37:01
Summary of Contents for VT-3413 W
