Vitek VT-1900 Manual Instruction Download Page 4

Page: 4 / 20

ENGLISH

•

Before using the unit for the first time, make sure
that the voltage in your mains corresponds to the
fan operating voltage.

USING THE REMOTE CONTROL (12)

•

Functions of the buttons on the remote control (12)
fully correspond to functions of the buttons on the
control panel (4).

ATTENTION!
The unit contains a lithium battery. Prevent children
from  swallowing  the  lithium  battery.  If  your  child
has swallowed a battery, immediately see your
doctor.
Battery leakage can cause injuries or damage the
unit. To avoid the unit damage, follow the instruc-
tions given below:
–  use only the «CR2025» battery;
–  do not recharge the battery;
–  insert the battery strictly following the polarity;
–  remove the battery if you are not planning to use

the unit for a long time;

– replace the battery timely.
– apply to specialized centers for further recycling

of the battery;

– avoid the power nippers circuit.

Installing or replacing the battery
in the remote control (12)

•

Remove the battery holder (13) by pressing the
side clamp, install a CR2025 battery, strictly follow-
ing the polarity.

•

Install the battery holder (13) back to its place.

Note: - if there is an isolation insert, remove the insert.

•

There is a remote control (12) storage (5) on the
fan body.

USING THE FAN

•

Plug the unit in, the display will light up, and the digi-
tal symbols (11) will show the room temperature.

Notes:
– every pressing of the control buttons is accompa-

nied by a sound signal;

– the air temperature indications may be slightly

different from the readings of another ther-
mometer.

•

Press the on/off button (6) «

POWER

» or the button (6)

POWER

» on the RC (12), the fan will switch on at the

first speed. After some time the display will show the
room temperature.

•

Select the speed mode by pressing the button (7)
«

SPEED

» or the button (7) «

SPEED

» on the RC (12). You

can select any of six speed modes which will be
shown on the display with the digital symbols (11)
«1-2-3-4-5-6».

•

Select the air flow mode by pressing the button (8) «

MODE

» or the button (8) «

MODE

» on the RC (12). You can

set two air flow modes which will be shown on the
display with the symbols:
«ПА» - the air flow speed will increase and decrease
gradually;
«SL» - night mode.

•

Select the auto-switch off operation time with the
button (9) «

TIMER

» or the button (9) «

TIMER

» on the RC

(12), the timer operation time will be shown on the
display by digital symbols. Available operation time
is from 1 hour to 12 hours with 1 hour setting step.

•

To switch the timer off, repeatedly press the but-
ton (9) «

TIMER

» or the button (9) «

TIMER

» on the RC (12),

until the timer operation time digital symbols (11) on
the display go out and the display shows the room
temperature.

•

To switch the oscillation mode on, press the but-
ton (10) «

OSC

» or the button (10) «

OSC

» on the RC

(12). To stop the oscillation mode, press the but-
ton (10) «

OSC

» or the button (10) «

OSC

» on the RC

(12) once again.

•

To switch the fan off, press the on/off button (6)
«

POWER

» or the button (6) «

POWER

» on the RC (12) and

unplug the unit.

MAINTENANCE AND CARE

•

Before cleaning the fan switch it off by pressing the
on/off button (6) «

POWER

» or the button (6) «

POWER

» on the

RC (12) and unplug the unit.

•

Do not use abrasive cleaners and solvents to clean
the fan.

•

Clean the unit body (2) with a slightly damp cloth
and then wipe it dry.

•

You can clean the air outlet grid (3) with a vacuum
cleaner using a corresponding attachment.

•

For easy cleaning of the grid (1) unscrew two fas-
tening screws and remove the grid (1), clean the
grid (1) and install it back to its place, tighten the
fastening screws (pic. 1).

•

Do not immerse the fan body (2), the power cord
and the power plug into water or any other liquids.

•

Make sure that no liquids get into the fan body (2) to
avoid its damage and prevent risk of electric shock.

STORAGE

•

Disconnect the fan from the mains and clean it.

•

Remove the battery from the RC (12) if you are not
going to use the fan for a long time.

•

Pack the fan into the original package and put it
away for storage in a dry cool place away from chil-
dren and disabled persons.

DELIVERY SET