4
The device is designed only for household
•
use, any commercial use of the juice extractor
is not allowed.
Before you start
Remove the device out of the package.
•
Before switching the device for the first time,
•
make sure that working voltage of the device
corresponds to electrical mains voltage.
Thoroughly clean all detachable parts, which
•
will be in contact with products, and dry
them.
Note
: Be careful when holding the filter-grater,
the grater has a sharp surface.
Wash vegetables/fruit, cut them into pieces,
•
which can easily come through the juice
extractor cover neck.
During squeezing of juice from “stone” fruit
•
(e.g. cherry, peach etc.), remove stones from
fruit.
Making juice
Put the juice extractor on flat dry and stable
•
surface.
Before assembling make sure that the device
•
is switched off and disconnected from
electrical mains.
Install the juice collector (5) on the motor
•
module (8).
Install the filter-grater (4) in the juice collector
•
(5).
Note
: in case of finding of mechanical damages
stop using the filter-grater.
Install the cover (3) on the juice collector and
•
fasten it with the help of the clamp (7).
Install the pulp container(10).
•
Connect the mains cable plug to socket.
•
Switch on the juice extractor by setting the
•
switch (9) to position “1” (low speed) or
position “2” (high speed).
Note
:
- “low speed” – for squeezing of juice from
soft vegetables/fruit (tomatoes, pears,
strawberries, oranges, plums, grapes,
pumpkin, onion, cucumbers etc.).
- “high speed” – for squeezing of juice from
hard vegetables/fruit (artichokes, carrot,
apples, pepper, beet, potatoes, pine-apples,
marrow, celery, spinach, dill, leek etc.).
Attention!
During treatment of products caus-
ing additional load to the motor
(viscous and/or
hard products), to avoid motor stoppage in the
process of operation and its further failure, it is
recommended to use high speed for squeezing
of juice (position “2”).
The juice extractor will switch on only if all
•
detachable parts are correctly installed, and
the cover (3) is fastened with the clamp(7).
Start loading products only with motor
•
running.
Gradually lower pre-cut pieces of vegetables
•
and fruit into the cover neck (2) and slightly
push them with the pusher (1). Do not apply
to much load to the pusher, as this can impair
quality of the resulted juice and even stop
rotation of the filter-grater (4). The more
slowly vegetables and fruit are treated, the
more juice you will get.
It is not allowed to put fingers and other
•
objects into the cover neck (2).
During operation, periodically check condition
•
of the filter-grater (4) against clogging of the
filter mesh with pulp, and if necessary, clean
the filter-grater (4).
If the filter mesh is clogged with squeezed
•
product, to avoid a failure of the device,
switch it off and clean the filter-grater (4).
Watch over filling up of the pulp container
•
(10). If the container is filled up, switch the
juice extractor off, take the cable plug out of
socket, and remove pulp from the container.
ATTENTION!
: Maximum allowed time of con-
tinuous operation should not exceed 2 minutes
with not more than 3 minutes break. After using
of the juice extractor, switch it off by setting the
switch (9) to position “0”, wait for a full stop of
the filter-grater (4) and take the cable plug out
of socket.
Carry out dismantling and cleaning of the
•
juice extractor after every use:
- Remove the pusher (1) out of the cover neck
(2).
- Lower the clamp (7) releasing the cover(3).
- Remove the cover(3).
ENGLISH
1636.indd 4
1636.indd 4
09.06.2011 11:38:42
09.06.2011 11:38:42
