4
ENGLISH
•
Do not wash the thermopot in a dishwashing
machine.
•
Before taking the unit away for long storage or
before cleaning, unplug it, pour out water and
let the unit cool down and dry.
•
For children’s safety reasons do not leave
polyethylene bags used as packaging unat-
tended.
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
•
Close supervision is necessary when children
or disabled persons are near the operating unit.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision of
a person who is responsible for their safety or
if they are not instructed by this person on the
usage of the unit.
•
Do not leave children unattended to prevent
using the unit as a toy.
•
Never use the unit if the power cord or the
power cord plug is damaged, if the unit works
improperly or after it was dropped.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any malfunc-
tion is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature keep it for at least three hours at
room temperature before switching on.
There may be water spots in the thermopot,
this is normal, as the unit has undergone fac-
tory quality control.
•
Unpack the thermopot; remove any promo-
stickers that can interfere with the unit opera-
tion.
•
Check the unit for damages, do not use it in
case of damages.
•
Make sure that the unit operating voltage corre-
sponds to the voltage of your mains.
•
Place the thermopot on a dry flat surface keep-
ing at least a 20 cm gap between the thermo-
pot body and the wall or furniture and at least a
30 cm gap above the thermopot.
•
Open the lid (8) by pressing the button (6) and
holding on it (pic. 1).
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (15) «МАКС».
•
Insert the power cord (16) connector into the
socket (12) on the thermopot body, and the
power cord (16) plug into the mains socket.
•
The control panel (5) will show the boiling mode
indicator (19) “BOILING” and the keep warm
mode indicator (24) “85°”. The keep warm tem-
perature “85°” is set by default.
Note: - during long water boiling the boiling mode
indicator (19) “BOILING” will be flashing.
•
After long water boiling the thermopot will
switch to the keep warm mode, the indica-
tor (19) “BOILING” will go out, the keep warm
mode indicator (21) “KEEP WARM” will be
flashing and the indicator (24) “85°” will glow
constantly.
Note: - the thermopot uses a long-boiling tech-
nology which allows to significantly reduce the
chlorine level in water.
•
Drain the water; to do this, you must unlock the
activation of the water pump by pressing the
button (27) “UN/LOCK”, the indicator (26) “ ”
will light up.
Attention! Be careful while draining the water to
avoid burns by hot water.
Version 1:
–
place a suitable bowl, for instance, a cup under
the spout (4) and press the water dispense but-
ton (3) with the rim of the cup.
Version 2:
–
place a suitable bowl under the spout (4)
and press the water dispense button (25)
“DISPENSE”.
Note: - the water is dispensed only when the
indicator (26) “ ” is switched on; if you have
pressed the button (27) “UN/LOCK” and haven’t
taken any action, the indicator (26) will go out in
10 seconds.
IM VT-1197.indd 4
01.08.2018 17:13:30
