Vitek 146526, Manual Instruction

Page: 5 / 32

5
ENGLISH
•
This table is only valid for smooth materials.
Fabrics of other types (crimped, raised, etc.)
are best ironed at low temperature.
• Sort items by ironing temperature first: syn-
thetics to synthetics, wool to wool, cotton to
cotton etc.
• The iron heats up faster than it cools down.
For this reason, it is recommended to iron the
items which require low temperature first (for
instance, synthetic fabrics). After that, start
ironing at higher temperature (silk/wool).
Cotton and linen items should be ironed last.
• If an item is made of mixed fabrics, the iron
should be set to the lowest temperature (for
instance, if an item is 60% polyester and 40%
cotton, it should be ironed at temperature
used for polyester ironing «
• »).
• If you cannot define the fabric structure, find
a spot that is inconspicuous when the item is
being worn and select the ironing temperature
experimentally (always start with the lowest
temperature and raise it gradually until you get
the desired result).
•
Corduroy and other fabrics that become glossy
quickly should be ironed strictly in one direc-
tion (in the direction of the pile) with slight
pressure.
• To avoid appearance of glossy spots on syn-
thetic and silk fabrics, iron them backside.
SETTING THE IRONING TEMPERATURE
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
• Turn the control knob (11) to set the required
ironing temperature: «
• », « •• », « ••• » or
« MAX », depending on the type of fabric, the
indicator (7) will light up.
•
Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go
out and you can start ironing.
Note:
• If you are ironing at high temperature but you
need to switch to lower temperature, wait until
the soleplate temperature decreases and the
indicator (7) lights up, and only then you may
start ironing.
WATER SPRAY
•
You can dampen the fabric by pressing the
water spray button (5) several times.
•
Make sure that there is enough water in the
water tank (10).
DRY IRONING
• Place the iron on its base (9).
•
Insert the power plug into the mains
socket.
• Set the continuous steam supply knob (3) to
the position
– the steam supply is off.
• Turn the control knob (11) to set the required
ironing temperature: «
• », « •• », « ••• » or
« MAX », depending on the type of fabric, the
indicator (7) will light up.
•
Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go
out and you can start ironing.
•
After you finish ironing, set the temperature
control knob (11) to the “MIN” position.
•
Pull the power plug out of the mains socket
and let the iron cool down completely.
STEAM IRONING
While steam ironing it is necessary to set the iron-
ing temperature «
••• », « МАХ ».
•
Place the iron on its base (9).
• Set the continuous steam supply knob (3) to
the position
– the steam supply is off.
•
Insert the power plug into the mains socket.
• Make sure that there is enough water in the
water tank (10).
• Turn the control knob (11) to set the required
ironing temperature: «
••• » or « MAX », the
pilot lamp (7) will light up.
• When the soleplate (13) reaches the set tem-
perature, the indicator (7) will go out, you can
start ironing.
• Turn the continuous steam supply knob (3) to
the position
or – steam supply is on,
steam will start going out from the iron sole-
plate (13) openings.
•
After you finish ironing, set the temperature
control knob (11) to the position «MIN», and
the continuous steam supply knob (3) to the
position
– steam supply is off.
• Pull the power plug out of the mains socket
and let the iron cool down completely.
ATTENTION!
If the steam is not constantly supplied during
operation, check whether the temperature con-
trol knob (11) is set properly and there is water in
the water tank (10).
BURST OF STEAM
The burst of steam function is useful for iron-
ing folds and can only be used at high ironing
IM VT-8316.indd 5 07.03.2019 14:14:12