Vita-Mix 120 VAC Models Owner'S Manual Download Page 21

Cooling the motor:

If the machine has overheated:

• The motor will stop and the message “MOTOR HAS

OVERHEATED REMOVE THE CONTAINER, THEN PRESS

START”, will scroll across the display window, while the words

“HOT SHUTDOWN” will remain in the display window alerting

you of the problem.

• The machine will not run until the container is removed and

the motor has cooled. Remove the container, shut the cover

door and press the START/STOP button, and run the machine

for two minutes.

• When the motor is cool “READY” will appear in the display

window.

If you cannot fix your machine with these suggestions, technical help is available by calling

800-4DRINK4 (800-437-4654), 440-235-0214. Outside the United States and Canada contact

your Vita-Mix distributor or contact Vita-Mix International at +1(440) 782-2450 or email

[email protected] for a local distributor or visit us at www.vitamix.com/foodservice.

MOTOR HAS OVERHEATED REMOVE..

HOT SHUTDOWN

READY

21

7. Problem:

• Machine is running irregular

• Display panel reads garbage

• “NO PROGRAM” is displayed when a

button is pushed

• Button pressed starts the wrong

program

• Machine starts by itself

• a specific program button is defective

• machine was turned off for a day,

week or month and turned on, there

was no power

• machine did not work right out of

the box

• machine works but no information

displayed on screen

• program buttons run the blender on

the same speed

Solution #1:

Turn the machine off and on again to reset

the programming.

Solution #2

Reset the machine to its original factory

settings. (Follow the instructions on page 7)

Solution #3:

Try plugging the machine into a new outlet.

Solution #4:

Call Vita-Mix Customer Service.

8. Problem:

• Display panel reads

Solution #1:

A new programming chip is needed. Call

Vita-Mix Customer Service.

9. Problem:

• Machine stops in the middle of its

blend cycle and resets; display panel

reads “VITA-MIX GENERAL

PROGRAM” then “READY”

Solution #1:

Plug the machine into its own power supply.

Solution #2:

Make sure the machine is not running on a

long extension cord.

CORRUPT DATA

Summary of Contents for 120 VAC Models

























Reviews: