D-301438 AMBER SELECT / AMBER SELECT
X
USER’S GUIDE
7
The AMBER SELECT / AMBER SELECT
X
calls your
Monitoring Center or a private phone and sends an
emergency alarm. When your Monitoring Center
representative or the person on the private phone
answers, you can hear them talking to you through the
AMBER SELECT / AMBER SELECT
X
.
If you have a phone connected to the AMBER SELECT /
AMBER SELECT
X
and want to use the phone to talk with
the representative, let the representative know and the
Monitoring Center will return your call.
Trouble
Trouble conditions are indicated by the flashing trouble
LED
and by the sounding of beeps, and are
immediately reported to the Monitoring Center.
Green LED
(power)
Definition
On
AC power and battery power OK
Flashes
AC or battery problem detected
Trouble messages are shown on the unit's display
(AMBER SELECT only) until they are resolved.
Pressing the CHECK button ( ) confirms the trouble
condition and cancels the beeps.
The AMBER SELECT / AMBER SELECT
X
continues to
transmit trouble messages every eight hours until the
problem is resolved.
Changing System Status
When the user wants to leave the premises, the unit
status must be changed to AWAY mode. The CHECK
button ( ) should be held down for 5 seconds
(3 seconds in Intrusion mode). The unit announces and
displays (AMBER SELECT only) AWAY – REMINDERS
OFF. In this state no medication reminders and no
pendant checks will be announced. The unit's speaker is
disabled and the yellow LED will turn off. In addition, in
AWAY mode inactivity detection is also disabled.
If the pendant transmitter button is pressed while in the
AWAY mode, the unit will sound "EMERGENCY" and
reports to the Monitoring Center. This initiates two-way
communication through the speaker. In addition, any
device that is alarmed while in AWAY mode immediately
initiates a call to the Monitoring Center (as in HOME
mode) and also initiates two-way communication.
To return the status to HOME mode, hold down the
CHECK button ( ) for 5 seconds. The unit's speaker will
announce and display (AMBER SELECT only) "HOME –
REMINDERS ON". The status LED (
) will turn on.
System status conditions are indicated by the yellow LED.
Yellow LED
Definition
Off
Away mode
On
Home mode
Flashes
Active reminder
Clock Adjustment /
Announcement
To Set the Clock (AMBER SELECT)
1.
To enter the clock adjustment mode, press the
CHECK button ( ) three consecutive times.
After each press, be sure to wait for the time
announcement to complete before pressing again.
The top line, assigned to the Month, will begin to flash.
2.
Use Direct Link buttons 1 (scrolls up) and 2 (scrolls
down) to set the current field value.
3.
Press Direct Link button 3 to scroll to select other
fields: month, day, year, hours, minutes, and
seconds.
4.
Press the Check button ( ) to set a new date or time
value.
Clock Announcement (AMBER
SELECT
X
)
Press the CHECK button to receive clock and status
announcement.
Note:
Clock adjustment is performed by the HHCPC
software.
Note:
Press the Call
(
)
button at any time to return
to normal operation mode. This does not affect
current time/date settings.
System Reset
To reset the system, simply insert a paperclip into the
reset switch hole, on the bottom of the AMBER
SELECT / AMBER SELECT
X
.
Alternatively, press the 3 speed dial buttons
continuously for four seconds.
RESET SWITCH
Figure 7
– Reset Switch
Direct link
The direct link buttons function as follows:
The AMBER SELECT / AMBER SELECT
X
dials the
programmed telephone number stored in memory
location 1, 2 or 3 and operates the unit as a speaker
phone.
Used for scrolling between fields when setting the
clock.
Used for adjusting the volume during two-way voice
communication with incoming calls or for calls
performed using the direct link buttons. Press direct
link button 1 to increase the volume or direct link
button 3 to decrease the volume.
Programming of the direct link buttons is performed by
the Monitoring Center. The stored telephone numbers
may be modified at any time.
01/15/2004
08:25:53 PM
