Vislink ADVENT DCU5000 Operation Handbook Download Page 11

Page: 11 / 42

Advent Communications

209297 – DCU5000 Drive Control Unit

Page 11 of 42

3.4.

SENSORS 2

This interface is designed to interface with any antenna fitted compass, GPS,
inclinometer or waveguide switch.

Detailed descriptions are beyond the scope of this manual. Contact Advent
Communications for further guidance and information.

Connector: 25-pin female D-type.

Pin Number Sensor Signal

description

Compass

RS232 – TX

RS232 – RX

C12V DC power. (0.5A max.)

4 GND
5 GND
6

GPS

GPS +12V DC power. (0.5A max.)

RS232 – TX

RS232 – RX

9 GPS

Enable

10 GND
14

Inclinometer

Trigger 1.

15 Trigger

Delta Pulse Width.

17 Angle

sign.

Pulse width 1.

+12V DC supply.

Pulse width 2.

21 GND
22 GND
23

Waveguide

Switch

Drive position 1.

11 Drive

GND.

Drive position 2.

Monitor position 1.

25 Monitor

GND.

Monitor position 2.

Summary of Contents for ADVENT DCU5000











































Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands

Vislink ADVENT DCU5000, Operation Handbook

Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands