background image

VISION X 

MANUFACTURER RECOMMENDATION

For those unfamiliar with electrical wiring on vehicles, Vision X 
recommends that all LED Lighting products are professionally 
installed

.

WIRING INSTALLATION INSTRUCTION

1.  Find a suitable place to mount Relay Part (R1) leaving 

enough room for Power & Ground wires Part (W1 & W2) 

to reach the battery & the Deutsch connector Part (C1) to 

reach the Light. Mount Relay.

2.  Run Power wire (W1) & Ground wire (W2) to the battery. 

Connect the Power wire (W1) to the Positive (+) battery 

terminal and connect the Ground wire (W2) to the Negative 

(-) battery terminal.

3.  Run the Deutsch connector wire (C1) to the light and plug 

in. 

4.  Disconnect the Switch Part (S1) at the white Plug Part (P1) 

and run the wire through the vehicles fi re wall to desired 

mounting location inside the Cab [using a factory rubber or 

plastic grommet is suggested]. 

5.  Drill the hole to the required size for the Switch (S1) and 

mount to desired position.

6.  Reconnect the Switch (S1) to the Harness. 

7.  Test Light. 

DIMMING FUNCTION

Your light is capable of dimming through the Prime Drive wire 
on the light’s plug. To achieve this requires our authorized     
accessories, the XIL-PDIMMER, or XIL-PDIMMERBUTTON. 

Do Not 

connect the Prime Drive wire without authorized        

accessories as this will damage the electronics.

Summary of Contents for Xmitter Prime Extreme









Reviews: