background image

VISION X 

MOUNTING INSTALLATION INSTRUCTION FOR FEET

1.  Start by setting the light bar in the location that you plan to 

mount it in. Mark each end of the light bar and measure the 

length.

2.  Depending on the length of your light bar, you will have a 

certain number of mounting feet Part (F1) included in the 

packaging. These feet fi t into grooves on the back of the 

light bar. [See Figure 1]

3.  Place each mounting foot (F1) bolt head fi rst into light bar 

rail grooves on the back of the light. [See Figure1] 

4.  Mark the location of each mounting feet on your vehicle. 

Drill holes for each. The feet can slide right to left inside the 

grooves, letting you fi ne tune the location.

5.  Remove the nut from the feet bolt, and place the light bar 

onto your  vehicle, line up the bolts with the previously 

drilled holes. (See Figure 2)

6.  Securely tighten the nut to the mounting feet bolt.

LIGHT ANGLE ADJUSTMENT

1.  Use the provided 6mm Allen wrench Part (A1) to loosen 

both Allen bolts on each side the light bar. Once desired 
angle is achieved, tighten the bolts.[See Figure 3]

2.  A good reference point is at 20 ft; the top of the beam 

should be 3” down from center of light (with the light bar at 

dead center). Tighten light and enjoy.

WARNING: Bolts, Nuts, and Washers are Stainless Steel. 
DO NOT USE Pneumatic or Electric Tools to Tighten and 
Loosen. The Hardware Will Permanently Lock Together.

Disassembled Foot Mount, included with every Vision 
X LED Light Bar. Comes assembled. 

Summary of Contents for Xmitter Prime Extreme









Reviews: