background image

DURALUX KIT

WARNINGS

As with many other high-tech products, this VISION X LED 
requires a bit of attention before you can use it. Please read 
the accompanying information carefully fi rst.
1.  Don’t stare directly into the light or shine directly into the 

eyes of another person as this may cause temporary loss 
of vision. 

2.  Never disassemble the products, as all parts must be 

factory serviced to insure proper operation.

3.  Don’t interchange the parts inside this light with other  

products. 

4.  The LED light is to be mounted on the vehicle only in a 

vertical, bottom mounting, or in a suspended position. 

5.  After turning on the light, the body might be hot enough 

to warrant a burn risk. Be careful when you touch the 
body after turning on the light for a long period of time. 

6.  Use the supplied wire harness for electrical installation. 
7.  The LED light must not adversely aff ect the performance 

of low beam, high beam, engine cooling or the driver’s 
view.

1

2

3

4

Qty: 2

Qty: 1

Qty: 2

DURA

Two Light   

Harness

Hex Head Bolt 

[M8]

Allen Key

[5mm]

[M

LIGHT

WIRING

PART (A1)

Qty: 2

PART (B1)

5

Qty: 2

Washer

[M8]

PART (W1)

6

Qty: 2

Nylock Nut

[M8]

PART (N1)

Summary of Contents for Duralux









Reviews: