Vision Works VWIC7WR Owner'S Manual Download

Page: 18 / 18

For the recording time of TF cards with different capacities, please refer to the table below. The

actual recording time is subject to the operating environment.

MODE

16G

32G

64G

128G

SINGLE

(640x480x1)

14h

28h

55h

110h

220h

QUAD

(320x240x4)

11h

22h

43h

86h

172h

SPLIT

(400x480x2)

13h

25h

50h

101h

201h

10. Troubleshooting

The symptoms described below do not necessarily mean a failure within the display.

Please check the following items before you initiate request for repair.

Symptoms

Possible Causes/Solutions

No picture, no

sound

Improper connection of automobile adapter. Use of un-authorized power supply.
Power switch is on OFF position.

No signal

Check whether the camera has power supply. Pair the monitor and the camera
again.

No sound

Check whether the sound volume is turned off or set too low.

Dark picture

Check whether brightness and contrast are adjusted correctly.

No color

Adjust the HUE settings.

Summary of Contents for VWIC7WR



















Search results

Summary of Contents for VWIC7WR

Reviews:

Related manuals for VWIC7WR

Brands by name

Popular brands

Vision Works VWIC7WR, Owner'S Manual

Search results

Summary of Contents for VWIC7WR

Reviews:

Related manuals for VWIC7WR

Brands by name

Popular brands