Viscount Prestige Organs Advanced Manual Download

Page: 68 / 80

Viscount - Advanced Manual

Prestige

9.3 UPDATING THE FIRMWARES

Prestige organs use two firmware packages:

OPERATING SYSTEM

: operating system controlling all the organ’s sections, the user

interface, the sequencer and the MIDI functions.
The update files for this section are called:

Prestige 100 and 80:

PK3Nxxxx.SYS

Prestige 70 and 60:

PK2Nxxxx.SYS

Prestige 50 and 40:

PK22xxxx.SYS

SOUND DRIVER

: sound generation firmware.

The update file for this section is called:

PRESCxxx.DRV

The “xxx” letters stand for the firmware release.

UPDATING THE OPERATING SYSTEM FIRMWARE

Switch on the organ keeping the CURSOR [

] and [

] buttons depressed, with the floppy disk

containing the update file inserted in the drive. The system will proceed to check the file on the
floppy disk:

SYSTEM FILE DETECTED

PK3N2200.SYS

Integrity and version checking

indicating the release of the firmware being installed:

Updating to

Operating Sys. Version 2.200

The file will then be read and loaded into the memory:

Loading System...

________________________________________

after which the relative check will be made.

Summary of Contents for Prestige Organs

















































































Search results

Summary of Contents for Prestige Organs

Reviews:

Related manuals for Prestige Organs

Brands by name

Popular brands

Viscount Prestige Organs, Advanced Manual

Search results

Summary of Contents for Prestige Organs

Reviews:

Related manuals for Prestige Organs

Brands by name

Popular brands