• Exit from the learning function is automatic
after approx.
8
seconds of the last operation
(or its interruption) and is signaled by a long
flash of the LED.To enter the learning func-
tion again repeat from b).
• To learn a new command on a button that
has already been memorized it is necessary
to first clear the memory (4.2)
4.2
) Cancellation procedures.
Cancellation procedures are used when wan-
ting to replace a learned command with
another learned command or restore a pre-
programmed command (See NOTE above).
4.2.A
) Cancellation of only one button.
a) Press and release the «
» button.
b) Enter the code «
6 6 6 6
».
c) Press the button to be cleared and watch
the LED that will confirm cancellation with
2 short flashes.
d) To cancel more commands repeat from a).
N.B.: Exit from cancellation mode is automatic
after approx.
8
seconds of the last operation.
4.2.B
)Total cancellation (on all buttons of both
memory banks).
a) Press and release the «
» button.
b) Enter the code «
7 7 7 7
» and watch the
LED that will confirm cancellation with two
short flashes.
5)
“WHAT TO DO IF…”
- After the batteries have been inserted, the
LED will not flash when pressing the
«
» button?
Check that the batteries have been inserted with
correct polarity.
- The automatic search was unsuccessful?
Repeat the operation and observe the
LED
After a while you will notice that the LED emits
5 short flashes indicating the end of a search
cycle. Keep the search button pressed…if
your machine still does not respond and the LED
again emits 5 short flashes, abandon this proce-
dure and try inserting manually, one by
one, following the procedures in the pre-
vious chapters, all the codes listed in the
tables (Tab. A for TVs,Tab. C. for VCRs).
- You have some difficulties with the learning
function?
Try repositioning the two remote controls chan-
ging the distance and/or alignment.
- After a while the operation of the remote
control becomes erratic?
Make a note of the codes memorized (see also
para.
3
) and quickly change the batteries. If no
change, press (for example with the tip of a pen-
cil or non sharp object) the internal reset button.
Take notice: after pressing the RESET but-
ton it is necessary to enter again all the
required codes.
CODE
?
CODE
?
CODE
?
4
TAB. B
ORIGINAL FINLUX MODELS
RC 300 - RC 3000 - RC 3001 - RC 3002 - RC 3008 - RC 3010 - RC 3011 - RC 322 - RC 323 - RC352 - RC 355 -
1003
RC 360 - RC 370 - SKYMASTER II - TC300
68200
1004
56770
1007
RC 1000 - RC 1002
1010
21 S 38 - 25 S 24 - 25 S 38 - 28 S 24 - RC 400 - RC 500 - RC 501 - RC 502 - RC 510 - RC 513 - RC 523 - RC 550
1013
TC 240
1016
INFR.REM.CONTR.
1017
RC 9000 - RD 9000
1018
400126 - 460201
1023
INFR.REM.CONTR.
1026
400111
1028
RC 571
1039
CODE
FINLUX
1003 - 1004
1007 - 1010
1013 - 1016
1017 - 1018
1023 - 1026
1028 - 1039
TAB. A:
CODES OF TV
ITT/NOKIA/S. LORENZ
1001 - 1002 - 1004
1005 - 1006 - 1007
1008 - 1012 - 1013
1015 - 1020 - 1021
1024 - 1029 - 1031
1039
LUXOR
1001 - 1002
1004 - 1005
1007 - 1009
1011 - 1013
1019 - 1022
1027
OCEANIC
1001 - 1002
1004 - 1005
1006 - 1007
1011 - 1012
1014 - 1027
1039
SALORA
1001 - 1002
1004 - 1005
1006 - 1009
1011 - 1012
1013 - 1020
1030 - 1031
1039
N.E. IT 9300 (GB) 13-07-2000 12:48 Pagina 4
