Virgin Pulse VP-13 Owner'S Manual Download Page 46

Page: 46 / 56

1.877.4VPULSE

www.virginpulse.com

4 6

The following indicators show the status of a message or of the unit.

INCOMPLETE DATA

Caller information has been interrupted during transmission

or the phone is excessively noisy.

ENTER NAME

Prompt telling you to enter a name for one of the 10 memory

locations.

ENTER TEL NUMBER

Prompt telling you to enter the telephone number for one of

the 10 memory locations.

DELETE ALL?

Prompt asking if you want to erase all Caller ID records.

DELETE?

Prompt asking if you want to erase one of the 10 numbers

stored in the phone's outgoing memory.

END OF LIST

Indicates there is no additional information in the Caller ID

memory log.

NEW

Indicates call or calls have not been reviewed.

UNKNOWN NUMBER/

The incoming call is from an area not serviced by Caller ID

NAME/CALLER

or the information was not sent.

PAGING

Someone has pressed the

page

button on the base.

BLOCKED NUMBER/

The person is calling from a number that has been blocked

NAME/CALL

from transmission.

DISPLAY MESSAGES

Summary of Contents for VP-13

























































Search results

Summary of Contents for VP-13

Reviews:

Related manuals for VP-13

Brands by name

Popular brands

Virgin Pulse VP-13, Owner'S Manual

Search results

Summary of Contents for VP-13

Reviews:

Related manuals for VP-13

Brands by name

Popular brands