Viper 5806V Page 50 Owner'S Manual Download | Manualshive

Page: 50 / 54

background image

46

© 2016 Directed. All rights reserved.

Warning! Safety First

Please read the safety warnings below before proceeding. Improper use of the
product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be performed
by an authorized Directed dealer. If you have any questions, ask your retailer or contact
Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command signal from
the remote control transmitter. Therefore, never operate the system in an enclosed area
or partially enclosed area without ventilation (such as a garage). When parking in an
enclosed or partially enclosed area or when having the vehicle serviced, the remote start
system must be disabled using the installed toggle switch. It is the user’s sole responsibil-
ity to properly handle and keep out of reach from children all remote control transmitters
to assure that the system does not unintentionally remote start the vehicle. THE USER
MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA
ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS
TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT
ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility of the user.

Manual Transmission Vehicles

Remote starters on manual transmission vehicles operate differently than those with auto-
matic transmission because you must leave your car in neutral. You must read this Owner’s
Guide to familiarize yourself with the proper procedures regarding manual transmission
remote starters. If you have any questions, ask your authorized Directed dealer or contact
Directed at 1-800-753-0600.

Before remote starting a manual transmission vehicle, be sure to:
•

Leave the vehicle in neutral and be sure no one is standing in front or behind the
vehicle.

•

Only remote start on a flat surface.

•

Have the parking brake fully engaged.

WARNING!

It is the responsibility of the owner to ensure the parking/emergency brake

properly functions. Failure to do so can result in personal injury or property damage.
We recommend the owner have the parking / emergency brake system inspected and
adjusted by a qualified automotive shop biannually.

Use of this product in a manner contrary to its intended mode of operation may result

«
...
48
49
50
51
52
...
»

Summary of Contents for 5806V























































Reviews:

No comments

Related manuals for 5806V

Brand: Bacharach Pages: 2

Brand: Bacharach Pages: 21

LIFESAVER silhouette 5800ACF

Brand: PSA Products Pages: 2

Brand: Audiovox Pages: 10

SmartSet CKS9005

Brand: Emerson Pages: 20

Brand: AAP Pages: 2

Brand: Audiovox Pages: 38

Brand: Trevi Pages: 8

Brand: Prestige Pages: 8

Brand: Prestige Pages: 16

Brand: B52 Pages: 14

Brand: Datexx Pages: 1

Brand: IKEA Pages: 16

Brand: La Crosse Pages: 2

Brand: La Crosse Pages: 10

Brand: iHome Pages: 16

Brand: iHome Pages: 20

Brand: Polon-Alfa Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands