background image

28

© 2016 Directed. All rights reserved.

28

Remote Pairing

Remote Pair is a process where the Responder LC and the system in 
the vehicle learn each others encrypted identification, securing their 
communication from intruders. Please note that your remote controls 
come already paired from the factory. However, if you wish to add a 
new remote control, the following instructions step you through pairing 
the LCD 2-way remote control to your system.

Note

Both the remote control and the vehicle need to be pre-
pared to initiate pairing.

Prepare the New Remote to be Paired with the System

1.  Make sure the remote control is set for the desired Car 1 or Car 

2 operation.

2. 

Press 

and 

hold

 the 

button for eight seconds. The remote beeps 

once,  

MAIN MENU

 is displayed (If Car 2 is on, ignore the Car 

Select text and beep after three seconds).

3. 

Release

 the 

button to display the Main Menu item list, 

 

SETUP REMOTE

 is displayed.

4.  Press the  

AUX

 or 

 button until 

PAIR REMOTE

 is displayed in 

the text field.  

5. 

Press 

and 

hold

 the 

 button until the remote beeps three times 

then release the 

 button.

6.  The remote control is now ready for pairing.

Note:

 The remote will exit Pairing Mode if there is no activity within 

30 seconds.

Prepare the Vehicle System to be Paired with a New Remote

1. 

Open 

at least one of the vehicle’s doors

.

2. 

Turn

 the key to the On position. 

Summary of Contents for 5706V





































































Reviews: