Vip2 VK2-1080VRD3V9 Installation And User Manual Download

Page: 73 / 77

VK2-1080VRD(IR)3V9(F) manual V1.0

3.8 Resetting to the factory default settings

To reset the Network Camera to the original factory settings, go to the Setup>System> Maintenance

web page (described in “3.5.5 System > Maintenance”) or use the Reset button (SW1) on the board of
the dome camera, as described below:

• Using the Reset Button

Follow the instructions below to reset the Network Camera to the factory default settings using
the Reset button.

1. Power off the Network Camera by disconnecting the power adapter.

2. Open the top cover of camera.

3. Press and hold the Reset button (SW1) on the board with your finger while reconnecting

the power.

4. Keep the Reset button (SW1) pressed during about 2 seconds.

5. Release the Reset button (SW1).

The network

camera

resets to factory defaults and restarts after completing the factory reset.

The unit now has the default IP address 192.168.30.220.

Close the top cover of camera.

Caution:

When performing a Factory Reset, you will lose any settings you have saved.

Summary of Contents for VK2-1080VRD3V9














































































Search results

Summary of Contents for VK2-1080VRD3V9

Reviews:

Related manuals for VK2-1080VRD3V9

Brands by name

Popular brands

Vip2 VK2-1080VRD3V9, Installation And User Manual

Search results

Summary of Contents for VK2-1080VRD3V9

Reviews:

Related manuals for VK2-1080VRD3V9

Brands by name

Popular brands