background image

Owner’s/Installer Manual Rev 1E 

UNPACKING 

Unpack the Griddle immediately after receipt. Remove the Gas Griddle from the crate; remove all packaging 

on and surrounding the unit and be certain to remove all protective plastics and residues from all surfaces. 

Make sure that all parts provided are located. Equipment must have the legs properly installed before use. 

Before using this equipment it must be cleaned and dried thoroughly. 

INSTALLATION 

NOTE: it is vital that the purchaser of this equipment post in a prominent location instructions to be followed in 

the event that the user smells gas. This information shall be obtained by consulting the local gas supplier. The 

purchaser of this equipment must post in a prominent location. 

1.

Read this manual thoroughly before installation and operation. DO NOT proceed with installation and

operation if you have any questions or do not understand anything in this manual. Contact your local

representative or 

VIONET

 first.

2.

Select a location for the Griddle that has a level, solid, nonskid surface that is nonflammable and

 

away

from water hazards or sinks, and is in a well-lighted work area away from children and visitors.

3.

This equipment but be installed under a proper ventilation as required by local code.

Local codes regarding installation and ventilation vary greatly by area. The National

 

Fire

Protection Association states in its NFPA 96 latest edition (see NFPA page at the

 

beginning of

this manual) that local codes are “authority having jurisdiction” when it comes to

requirements for installation of equipment. Therefore, installation should comply with all local

codes.

4.

Screw legs into (A) the permanently fastened nuts on the four corners of the unit and tighten by hand.

Legs must be installed to adequately provide proper ventilation to the unit.

5.

Level unit by adjusting the four feet and tighten securely. The adjustable feet have an adjustment of

one inch. Do not slide unit with legs mounted. Lift if necessary to move unit.

6.

The supplied gas pressure regulator is factory set at 4” Natural Gas W.C. or 10” Propane Gas.

7.

THESE UNITS ARE SUITABLE FOR INSTALLATION ON NON-COMBUSTIBLE SURFACE ONLY.

Noncombustible clearances: 6” sides (152 mm), 6” rear (152 mm), 4” floor (102 mm).

8.

Do not obstruct the flow of combustion and ventilation air under the unit by the legs or behind the unit

by the flue. Do not place objects between the bottom of the unit and the counter top.

9.

There must be adequate clearance for removal of the front panel. All major parts except the burners

are removable through the front if the gas is disconnected.

10.

It may be necessary to adjust the balance of gas volume and air supply to each burner. This must be

done by and authorized service technician.

11.

Pipe threading compound must be resistant to the action of liquefied petroleum gas. DO NOT USE

TEFLON TAPE.

The installation of this appliance must conform to local codes, or In the absence of local codes, the 

National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA 

B149.1, as applicable. 

The appliance and its individual shut off valve must be disconnected from the gas supply piping

system during any pressure testing of that system at test pressures in excess of ½ PSI (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual

shut off valve during any pressure testing of the gas supply piping system at test pressures equal to

less than ½ PSI (3.5kPa).

 

DO NOT use an open flame to check for leaks. Check all gas piping for leaks with a soap 

and water solution before operating the unit.

 

As continued product improvement is a policy of Vionet, specifications are subject to change.

8830 Siempre Viva Road Suite 100  |  San Diego CA 92154  |  

https://www.vionetequipment.com

Summary of Contents for GAS COUNTER SERIES















Reviews: