manualshive.com logo in svg

Vintage Air 754562, Manual

Share
Download
Vintage Air 754562 Manual Download Page 6

6

www.vintageair.com

905458 REV E 07/10/18, PG 6 OF 29

Engine & Passenger Compartment

Disassembly

1.

2.
3.
4.
5.
6.
7.
8.
9.

10.
11.
12.

Disconnect battery. Ensure that the cable remains disconnected throughout the entire installation process. 

NOTE: Battery is located under passenger floorboard.

Drain radiator.
Remove OEM heater hoses (discard).
Remove OEM heater/blower assembly if installed (discard) (See Photo 1, below).
Remove OEM heater wiring (discard).
Remove glove box door (retain).
Remove glove box (discard, but retain OEM screws).
Disconnect all wires and cables from OEM control panel (discard).
Disconnect all wires and cables from OEM heater control knobs (discard).
Remove OEM defrost ducts (discard).
Remove the defrost vent garnish/cover (retain) (See Photo 2, below).

Remove the round cover from the firewall (See Photo 3, below).

NOTE: Before starting the installation, check the function of the vehicle (horn, lights, etc.) for proper 

operation, and study the instructions, illustrations, & diagrams.
Perform the Following:

Photo 1

Photo 2

Photo 3

OEM Heater Assembly

Defrost Vent Garnish/Cover

Firewall Cover

Summary of Contents for 754562































Reviews:

No comments

Brands by name

Popular brands

Load more brands