background image

 

Chapter 1: Introduction & Manual Overview 

 
This system is a reliable, high performance, high speed, standalone manual duplication system. 
With  its  professional  industrial  design  and  simple  user  interface,  it  will  make  the  duplicating 
experience easier than ever.  

 

Before getting started: 

 

Before starting to use this system, please read the following to ensure proper operation: 
 

1. 

Temperature Warning: 

If  the  system  was  stored  in  a  location  where  the  temperature  dropped  below  32

F  (0

C) 

within the past 24 hours, please leave the system in a warm room with a temperature of at 
least 65

F (19

C), for 4 hours prior to powering on the unit for the first time. Failure to do so 

may cause irreparable harm and prevent the system from functioning properly. 
 

2. 

Maintenance: 

It is very important to operate and keep the system in a dust free, clean environment since 
dust  is  the  number  one killer  of  electronic  devices.  Failure  to  do  so may  severely  damage 
the system. It is strongly suggest that an Air Cleaner be placed next to the system and that 
an air duster (canned air) be used consistently to clear off any dust, which may accumulate 
on the surface of the system. 

 

3. 

Proper Shutdown: 

To avoid possible system failures, the system needs to be shutdown properly. To shutdown 
the system, press the Up or Down Arrow button until the “Shutdown” menu is appears and 
then press the “ENT” button. Follow the instructions on the screen to shutdown the system 
properly.  Turning  off  the  system  without  performing  this  function  will  increase  the  risk  of 
damage to the system. 

 

Summary of Contents for Hard Drive Duplicator 1.0



























Reviews: