background image

                                                       

 

                       

 

- 12 - 

 
 
e.  Malfunctioning fans 
 
f.  Evaporator or condenser airflow 

 

g.  Dirty Condenser 
h.  Iced evaporator 
i.  Refrigeration system restriction 
j.  Refrigerant leak 
k.  Undercharge or overcharge 
l.  Failed components 
 

minimum  1  foot  clearance  for  the 
ambient air intake side  

e.  Check  for  both  evaporator  and 

condenser fans  

f.  Check  for  air  restrictions,  air  short-

circulation, grille directions 

g.  Clean condenser 
h.  Defrost and reset temperature 
i.  Call service 
j.  Call service  
k.  Call service  
l.  Check  compressor  windings,  start 

relay and overload protector 

7. Unit running too 

long 

 

a.  Improper cellar insulation & seal 
 
b.  Exhaust restricted 
 
 
 
c.  Cellar too large 
d.  Ambient temperature > 90°F 
e.  Dirty Condenser 
f.  Improper condenser air flow 
 

a.  Check  insulation,  gasket  and  door 

opening 

b.  Leave minimum 3 feet clearance for 

the  hot  air  exhaust  side  and  leave 
minimum  1  foot  clearance  for  the 
ambient air intake side 

c.  Check for excessive size   
d.  Check for installation location 
e.  Clean condenser 
f.  Check  for  fan  and  air  short 

circulation 

8. Condenser fan 

running but 
compressor 
not running

 

a.  Incorrect or loose wirings 
b.  Failed components 

 

c.  Liquid 

refrigerant 

in 

the 

compressor 

a.  Check all wirings and  connections 
b.  Check  start  relay,  start  capacitor, 

overload protector, compressor. 

c.  Call service. 

9. Compressor 

running but 
condenser fan 
not running

 

a.  Fan blade stuck 
b.  Incorrect or loose wirings 
c.  Failed motors 
d.  Fan cycle control 

a.  Check for proper clearance 
b.  Check all wirings 
c.  Call service 
d.  Check for setting 

10.Temperature  

high, 
compressor 
stopping and 
starting but 
very short 
running time

 

a.  Failed components 
 
b.  Improper condenser airflow 
c.  Dirty condenser 
d.  Overcharge of refrigerant 
e.  Discharge  or  suction  pressure 

too high 

a.  Check  compressor  windings,  start 

relay and overload protector. 

b.  Check for condenser fan  
c.  Clean condenser 
d.  Call service for removing refrigerant 
e.  Call service for information 
 

11.Evaporator fan 

running too 
long 

a.  Post-compressor  fan  running 

mode for humidity modulation 

 

a.  Reset FON 
 

12. Evaporator fan 

running but 
condensing 
unit not 
running

 

a.  Incorrect or loose wirings 
b.  Failed components 
 
c.  Low refrigerant 

a.  Check all wirings and  connections 
b.  Check  start  relay,  start  capacitor, 

overload protector, compressor. 

c.  Call service 
 

13.Temperature 

low 

a.  Low temperature setting 
b.  Low ambient temperature 
c.  Air probe fault 
 
d.  Temperature controller fault 

a.  Raise the setting 
b.  Move to another location 
c.  Check probe connections or change 

a new one 

d.  Change a new one 

14.Evaporator 

freezing up

 

a.  Evaporator air flow restriction 
b.  Condenser air flow restriction 

a.  Check for fans and CFM 
b.  Check for fans and CFM 

Summary of Contents for WINE-MATE WM-2500SSO






























Reviews: