background image

Securely glue together. If coming 
off during flight, you lose control 
of your air plane.

 3-Repeat the previous procedures to hinge the second 
    elevator to the other side of the horizontal stabilizer.    

Vergewissern Sie sich, sauber geklebt zu haben. 
Andernfalls konnen Probleme mit der Flugeigenschaft 
auftreten!

CA

Note: The slot for the elevator control horn installation is 
pre- cut at factory.

1-Trial fit the hon. Actuate rudder linkage 
   manually it should not be hard spot. 
   Adjust if necessary. 

2-Insert the plate through the foot of the horn.
   Bond with 

thin CA glue.

Plastic control horn

....................2

FIN

RUDDER

11- Elevator

CA

Thin CA

13- Nose gear

1

Landing gear steering horn

4

1-Pull the magnetic top hatch out of the fuselage, then turn the fuselage 
   over and Insert “Z” bend of steering linkage inside the hole of front 
   landing gear steering horn.
2-Position the steering horn inside the front landing gear mount already
   attached to the firewall.
3-Slide front leg into the bearing and through the horn.
4-Screw steering horn on the leg.

Nose gear mount

3x12mm screw...4

Steering horn...1

..............1

FUSELAGE - BOTTOM VIEW

2

3

4

FUSELAGE - BOTTOM VIEW

FUSELAGE - BOTTOM VIEW

1.2x500mm rod

.................1

4mm collar

.............2

With electric retract and
struts (option).

Summary of Contents for PILATUS PC-7













Reviews: