background image

 

 

 

 

 

Disclaimer 

 
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF VINCOTECH 
GMBH. IT MAY NOT BE COPIED OR TRANSMITTED BY ANY MEANS, PASSED 
TO OTHERS, OR STORED IN ANY RETRIEVAL SYSTEM OR MEDIA, WITHOUT 
PRIOR CONSENT OF VINCOTECH OR ITS AUTHORIZED AGENTS. 
 
THE INFORMATION IN THIS DOCUMENT IS, TO THE BEST OF OUR 
KNOWLEDGE, ENTIRELY CORRECT. HOWEVER, VINCOTECH CAN NEITHER 
ACCEPT LIABILITY FOR ANY INACCURACIES, OR THE CONSEQUENCES 
THEREOF, NOR FOR ANY LIABILITY ARISING FROM THE USE OR 
APPLICATION OF ANY CIRCUIT, PRODUCT, OR EXAMPLE SHOWN IN THE 
DOCUMENT. 
 
THE PRODUCT (HARD- AND SOFTWARE) DESCRIBED IN THIS DOCUMEN-
TATION IS NOT AUTHORIZED FOR USE IN LIFE SUPPORT DEVICES OR 
SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF VINCOTECH. 
 
THIS DOCUMENT MAY PROVIDE LINKS TO OTHER WORLD WIDE WEB SITES 
OR RESOURCES. BECAUSE VINCOTECH HAS NO CONTROL OVER SUCH 
SITES AND RESOURCES, VINCOTECH SHALL NOT BE RESPONSIBLE FOR 
THE AVAILABILITY OF SUCH EXTERNAL SITES OR RESOURCES, AND DOES 
NOT ENDORSE AND IS NOT RESPONSIBLE OR LIABLE FOR ANY CONTENT, 
ADVERTISING, PRODUCTS, OR OTHER MATERIALS ON OR AVAILABLE 
FROM SUCH SITES OR RESOURCES. VINCOTECH SHALL NOT BE 
RESPONSIBLE OR LIABLE, DIRECTLY OR INDIRECTLY, FOR ANY DAMAGE 
OR LOSS CAUSED OR ALLEGED TO BE CAUSED BY OR IN CONNECTION 
WITH USE OF OR RELIANCE ON ANY SUCH CONTENT, GOODS OR 
SERVICES AVAILABLE ON OR THROUGH ANY SUCH SITE OR RESOURCE. 
 
VINCOTECH RESERVES THE RIGHT TO CHANGE, MODIFY, OR IMPROVE 
THIS DOCUMENT OR THE PRODUCT DESCRIBED HEREIN, AS SEEN FIT BY 
VINCOTECH WITHOUT FURTHER NOTICE. 

V1.5 – Dec-09 

User’s Manual 

Page 3 of 37

 

Summary of Contents for A1035-H






































Reviews: