background image

 

16) Fire Alarm Certification to EN54-3 
 

The BExS110D, 24Vdc variant, with flare style horn, is certified for use as a Sounder in Fire Alarm Systems according to Regulation 
EU No. 305/2011: Construction Products Regulation (CPR), and also holds VdS Approval for Components and Systems for use in 
Fire Alarm Systems. 
 
EC Type Examination Certificate: 0708-CPD-20225 
VdS Approval No.: 

 

G 206011 

Notified Body: 

 

 

VdS Schadenverhütung GmbH 

Notified Body No.: 

 

0786 

Standards applied: 

 

EN 54-3:2001 + A1:2002 

Supply 

voltage: 

  18-30Vdc 

 
The Sounders are certified for tones 2, 3, 9, 15, 16 and 17. For SPL levels at min. and max. supply voltage see tables below. 
 

BExS110D

 

(Input Voltage 18V)

 

Tone No. and 

Frequency Description 

Horizontal Plane (0°) 

Vertical Plane (90°) 

15° 45° 75° 105° 

135° 

165° 15° 45° 75° 105° 

135° 

165° 

2

 - 800/1000Hz @ 0.25 

Sec Alternating

 

104.7 105.1 108.0 106.7 103.4 102.1 104.2  106.0  107.2 106.8 103.4 101.7 

3

 - 500/1200Hz @ 

0.3Hz 0.5 Sec Slow 
Whoop

 

106.8 108.9 108.8 107.0 107.6 104.6 106.1  107.6  109.6 109.1 106.9 105.6 

9

 - 1200/500Hz @ 1Hz 

- DIN / PFEER 
P.T.A.P.

 

105.6 106.8 107.4 106.4 106.2 103.6 104.1  105.3  106.8 106.7 105.0 103.3 

15 

-  800Hz Continuous

 

100.1 103.3 105.6 107.6 103.0 100.3  10.2  102.9  105.2 106.8 102.4  99.6 

16

 - 660Hz 150mS ON 

150mS OFF 
Intermittent

 

92.5 93.9 97.9 97.5 92.5 91.5 92.1 94.5 98.5 97.9 93.1 92.2 

17

 - 544Hz  

(100mS)/440Hz 
(400mS) - NF S 32-
001

 

101.0 102.5 106.5 107.5 103.9 100.7 101.7  102.5  105.7 107.9 103.6 101.5 

BExS110D

 

(Input Voltage 30V)

 

Tone No. and 

Frequency Description 

Horizontal Plane (0°) 

Vertical Plane (90°) 

15° 45° 75° 105° 

135° 

165° 15° 45° 75° 105° 

135° 

165° 

2

 - 800/1000Hz @ 0.25 

Sec Alternating

 

105.0 106.9 109.9 109.0 105.3 103.3 104.8  106.6  109.6 109.9 104.8 103.5 

3

 - 500/1200Hz @ 

0.3Hz 0.5 Sec Slow 
Whoop

 

105.9 107.9 109.2 108.7 107.7 106.4 105.2  108.6  109.3 109.3 106.7 107.2 

9

 - 1200/500Hz @ 1Hz 

- DIN / PFEER 
P.T.A.P.

 

106.4 107.0 108.1 107.9 107.4 104.8 107.3  107.9  108.5 108.6 108.1 105.8 

15 

-  800Hz Continuous

 

102.3 103.9 105.5 107.8 105.7 102.8 102.0  104.5  106.9 107.0 106.7 103.5 

16

 - 660Hz 150mS ON 

150mS OFF 
Intermittent

 

94.7 96.3 97.8 98.8 94.5 94.2 95.3 97.6 98.8 99.3 96.0 93.8 

17

 - 544Hz  

(100mS)/440Hz 
(400mS) - NF S 32-
001

 

103.3 105.7 108.5 109.1 106.1 102.2 104.2  105.6  107.7 108.7 106.3 102.0 

 

www.acornfiresecurity.com

www.acornfiresecurity.com

Summary of Contents for BExS110D









Reviews: