AGM
AGM EH 1505 (GB)
15
Warning
Every time you use the drill you should verify the following:
1.
Hex bit is secure.
2.
Oil level is full.
3.
Select to the function you want to do before you engage in the proposed operation
4.
All safety apparel. Safety Glasses Safety Shoes. Safety Gloves. Ear Defenders and
Safety Hat are being worn.
Failure to adhere to these safety rules can greatly increase the chances of injury.
Maintenance
Oil feeding
Caution
Prior to oil feeding, always disconnect the plug from the power supply receptacle. Since
an oil chamber is built in this electric hammer chisel, it can be used for approximately 20
days without supplying lubrication oil, assuming that the chisel is used continuously 3
–
4
hours daily.
Feed oil into the oil tank as described below before using the hammer chisel. (See Fig 6 )
-
When the chisel is held upright look through the oil gauge window to see if oil is
visible, if no oil shows oil must be installed before operating. If chisel is used without
oil this could seriously damaged the chisel and forfeit any warranty given.
-
Before feeding oil, use the provided wrench to remove the oil gauge. Be careful not
to lose the rubber packing attached below the oil gauge.
-
Check the oil level once daily, confirming that oil is filled.
-
After feeding oil, securely clamp the oil gauge.
Fig 6
Note
: Oil for the electric hammer chisel is sold separately.
Summary of Contents for AGM EH 1505
