Viking VIPR102 Instruction Manual Download Page 1

1

VIKING RANGE, LLC

Downdraft Ventilators

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 
TO PERSONS, OBSERVE THE FOLLOWING:

1.  Use this unit only in the manner intended by the manufacturer. 

If you have questions, contact the manufacturer at the address 
or telephone number in the warranty.

2.  Before servicing or cleaning unit, switch power off at service panel 

and lock the service disconnecting means to prevent power 
from being switched on accidentally. When the service 
disconnecting means cannot be locked, securely fasten a 
prominent warning device, such as a tag, to the service panel.

3.  Installation work and electrical wiring must be done by a qualifi ed 

person(s) in accordance with all applicable codes and standards, 
including fi re-rated construction codes and  standards.

4. Suffi cient air is needed for proper combustion and exhausting 

of gases through the fl ue (chimney) of fuel burning equipment 
to prevent backdrafting. Follow the heating equipment 
manufacturer’s guideline and safety standards such as those 
published by the National Fire Protection Association (NFPA), 
and the American Society for Heating, Refrigeration and 
Air Conditioning Engineers (ASHRAE), and the local code 
authorities.

5.  When cutting or drilling into wall or ceiling, do not damage 

electrical wiring and other hidden utilities.

6.  Ducted fans must always be vented to the outdoors.
7.  To reduce the risk of fi re, use only metal ductwork.
8.  Do not install this product with the activating switch directly 

behind a burner or element. Minimum distance between the 
switch and the edge of the burner should be 4 inches.

9. Loose-fi tting or hanging clothing should never be worn when 

operating this appliance. They may be ignited by burners/
elements on cooktop.

10. Children should not be left alone or unattended in the area 

where this appliance is in use.

11. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

 

a)  Never leave surface units unattended at high settings.    
Boilovers cause smoking and greasy spillovers that may  

 

ignite. Heat oils slowly on low or medium settings.

 

b)  Always turn hood ON when cooking at high heat or when 
cooking fl aming foods.

 

c)  Clean ventilating fans frequently. Grease should not be   
allowed to accumulate on fan or fi lter.

 

d)  Use proper pan size. Always use cookware appropriate   
for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE 
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE 
FOLLOWING

a

:

 

1.  SMOTHER FLAMES with a close-fi tting lid, cookie sheet,  
or metal tray, then turn off the burner. BE CAREFUL TO  

 

PREVENT BURNS. If the fl ames do not go out immedi 

 

ately, EVACUATE AND CALL THE FIRE DEPARTMENT.

 2. 

NEVER PICK UP A FLAMING PAN - You may be burned.

 

3.  DO NOT USE WATER, including wet dishcloths or towels 
- a violent steam explosion will result.

 

4.  Use an extinguisher ONLY if:

 

 A.  You know you have a Class ABC extinguisher, and you    
 

already know how to operate it.

       B. The fi re is small and contained in the area where it  

 

 started.

       C. The fi re department is being called.
       D.  You can fi ght the fi re with your back to an exit.

a

 Based on “Kitchen Firesafety Tips” published by NFPA.

MODEL WIDTH 

BLOWER 

(purchase separately)

VIPR102 

30"

 

VIDV500 Interior or VEDV900 Exterior

VIPR102R 

30" w/ remote control

 

VIDV500 Interior or VEDV900 Exterior

VIPR162 

36"

 

VIDV500 Interior or VEDV900 Exterior

VIPR162R 

36" w/ remote control

 

VIDV500 Interior or VEDV900 Exterior

VIPR182 

48"

 

VIDV500 Interior, VEDV900 Exterior or VEDV1200 Exterior

VIPR182R 

48" w/ remote control

 

VIDV500 Interior, VEDV900 Exterior or VEDV1200 Exterior

WARNING - RANGETOPS ONLY: 

To reduce the risk of burns or ignition of clothing by reaching across burners, an "R" model 

downdraft (with remote control) 

MUST 

be used with a rangetop. The remote control 

MUST

 be mounted in the countertop - at least 

4" from the burners. See "INSTALL COOKTOP" section on page 8.

!

INSTALLER: 

Save this manual for Electrical Inspector and 

Homeowner to use.

HOMEOWNER: 

Use and Care Information on Page 11.

CAUTION

1.  For general ventilating use only. Do not use to exhaust 

hazardous or explosive materials and vapors.

2.  To avoid motor bearing damage and noisy and/or unbalanced 

impellers, keep drywall spray, construction dust, etc. off power 
unit.

3. Clean fi lters and grease-laden surfaces frequently.
4.  Do not repair or replace any part of this appliance unless 

specifi cally recommended in this manual. All other servicing 
should be done by a qualifi ed technician.

5.  Please read specification label on product for further 

information and requirements.

6.  DO NOT INSTALL WITH GRILL MODEL RANGETOPS. This 

will void the warranty.

7. 

Models VIPR102SS, VIPR162SS, and VIPR182SS (non-
remote units): 

DO NOT INSTALL WITH RANGETOPS. This 

will void the warranty.

!

 INTENDED FOR DOMESTIC COOKING ONLY 

!

Summary of Contents for VIPR102









































Reviews: