17
The one or two digit code stored in the Relay Activation Command is the touch tone command that the person being
called must enter on their phone in order to actuate relay 1 or 2 to control a doorstrike, mag-lock, gate controller, or
other device. The code can contain the numbers 0 - 9, 00 - 99, ## or
. The code cannot match a relay latching or
toggle command (11, 10, 1#, 21, 20, or 2#). The code must be entered while the remote phone is communicating with
the Entry phone. The Entry phone determines which direction the touch tone is coming from and only responds to
touch tones from the called phone.
Factory Setting:
Relay 1 -
,
Relay 2 -
Q
2
18. Relay 1 or 2 Act (Activation) Command
The value stored in the Relay 1 or 2 Activation Time is the amount of time relay 1 or 2 will be energized after a correct
touch tone command is entered. This number can range from 0.5 - 99 seconds.
Note:
This also affects timing in
Doorbell Mode.
Factory Setting:
5 seconds
19. Relay 1 or 2 Activation Time
Doorstrike Mode (Factory Setting):
When programmed for Doorstrike Mode the relay will momentarily activate for
the preprogrammed relay activation time after detecting the correct relay activation command (one or two digit touch
tone) from the called party.
Outbound Call Mode:
When programmed for Outbound Call Mode the relay will activate continuously for the duration
of any outbound call from the Entry phone.
Inbound/Outbound Call Mode:
When programmed for Inbound/Outbound Call Mode the relay will activate
continuously for the duration of any inbound or outbound call to or from the Entry phone. This mode is useful for turning
on IR flood lights, for VoIP phones with cameras, etc.
Doorbell Mode:
When programmed for Doorbell Mode the relay will momentarily activate the relay for the
preprogrammed relay activation time at the beginning of any outbound call from the Entry phone. This mode is useful
for activating a door chime, etc. When activating door chimes, a 0.5 - 1 second relay activation time is recommended.
Alarm Mode:
When programmed in Alarm Mode the relay will activate continuously while the Entry phone is powered
and registered to the SIP server. In the event the unit loses power and/or SIP registration the relay will turn off, which
can be used to signal an alarm device.
NOTE:
Relay 2 should be set to “Alarm Mode” when mounting a
PRX-3
in close
proximity of the
K-1700-IP
(when mounting the
K-1700-IP
and
PRX-3
to a
PRX-3-MK-GNP
gooseneck pedestal
mounting plate) See Page 25.
Ring Mode:
When programmed for Ring Mode the relay will continuously activate while the ringing extension is called.
This mode is useful for activating a Viking model
SL-2
strobe light, etc.
Ring Flash Mode:
When programmed for Ring Flash Mode the relay will momentarily turn on and off in a 400ms
on/off cadence while the ringing extension is called. This mode is useful for activating a Viking
LPL-1
Remote Visual
Indicator, etc.
17. Relay Mode
20. Relay Activation Delay
A relay activation delay of 0.5 - 99 seconds can be programmed in the
K-1700-IP
. A relay activation delay is useful in
two door vestibule entrance applications. This allows you to program a delay time from when relay 1 (outside door) is
activated to when relay 2 (inside door) is activated. The programmed delay time should be set to the average time it
takes a person to walk from the outside door to the inside door.
When a request for exit (REX) is activated, relay 2 will activate first, then after the programmed delay relay 1 will
activate.
Factory Setting:
Disabled
The relay activation tone is a buzzing sound that is heard at the Entry phone when the door strike relay is activated.
After the called party enters the correct relay activation command, the called party will hear 2 short confirmation beeps
and the entry phone will output a buzzing sound (relay activation tone) while the door strike relay is activated. The tone
(buzz) length will match the relay activation time up to a maximum of 5 seconds. The tone (buzz) can be programmed
to three different volume settings 1 = Low, 2 = Medium, 3 = High or it can be disabled.
Factory Setting:
3
21. Relay Buzz Volume