13
12
INSTALLATION OVERVIEW
The ice machine must:
• Be connected to cold, potable water.
• Be connected to a drain.
• Be connected to the proper power supply.
• Be able circulate air through the vents at the front.
Note: DO NOT
build in so that the door is recessed. Door is meant to be flush with surronding cabinetry, but
not recessed.
INSTALLATION PARTS
The following installation parts are supplied with the ice machine:
2
-Hinge covers
2
-Door stop pins
2
-Hinge side covers
10
-#8 sheet metal screws
2
-Hole plugs
2
-8-32 Machine screws
2
-Hinge opening covers
4
-Leveling leg caps
1
-Upper door bracket (LH)
2
-Black kickplate screws
1
-Lower door bracket (LH)
1
-Access panel button cover
ACCESSORY DOOR PANEL
The ice machine is supplied without a finished door panel. Accessory door panels are offered or a custom panel may
be used.
Accessory Door Panel Attachment
Note:
If door swing is to be changed, it must be done before
panel is attached.
To attach a door panel:
The panel will be held on by 6 screws (supplied with door panel)
and 2 machine screws (supplied with ice machine).
1. Remove the gasket and retain for later use.
2. If the door panel is stainless steel, remove any plastic covering
the stainless steel panel.
3. Place the panel onto the outside of the door, and secure it to
the door using two machine screws, located at the left center
and right center ( behind door gasket).
4. Fasten the panel to the door using the 6 screws (supplied with
door panel). In the hinge area, use the outermost screw holes.
5. Place the covers over the hinge areas, and secure each cover to
the door using a screw (supplied with door panel).
6. Insert hole plug over screw installed in step 5 (supplied).
7. Return the gasket to its original position.
CUSTOM PANEL
A custom panel of wood or other material not exceeding 15 lb can be attached to the door. Attachment is from the ice
side of the door. Holes are provided in the door for this purpose.
To create and attach a custom panel:
•
Panel width: 14-7/8” (37.9 cm)
•
Panel height: 30-5/16” (77.0 cm)
•
Panel thickness: 5/8” (14.5 cm) to 3/4” (1.9 cm)
1. Measure overall height of cabinet opening where ice machine will be (floor to botom of countertop edge).
2. Determine desired kickplate space (from bottom of door to floor). This could be equal to the adjacent cabinet’s
kickplate space or another space the user wants.
3. Subtract kickplate space from cabinet opening.
Hole
plug
Cover
Gasket
4. Subtract 1/8” or more for clearance space between top of door and bottom of countertop edge from cabinet
opening. This is the maximum door length.
5. Cut panel to width
6. Cut panel to length (cabinet space - kickplate space - top clearance = length).
7. Determine top of panel.
8. Mark hole locations using drawing on the back of these instructions. Drawing assumes top of panel will be flush
with top of door. Measure hole locations from the top of the panel.
9. Drill pilot holes for wood screws. Use drill stop to prevent drilling through the panel.
10. Mount panel to door using wood screws or supplied panel mounting screws.
Note:
When installed, ice machine must be adjusted for height to position top of door to desired clearance.
13-9/16”
(34.4 cm)
8-1/4”
(20.9 cm)
6-25/32”
(17.7 cm)
4-1/8”
(10.5 cm)
13/16”
(2.4 cm)
13/32”
(1.3 cm)
13/32”
(1.3 cm)
14-7/8”
(37.9 cm)
30-5/16”
(77.0 cm)
14-11/16”
(37.3 cm)
ø 1/8”
TYP. (10)
13-31/64”
(34.3 cm)
CUSTOM PANEL DIMENSIONS