background image

22

Related Products

ADA Compliant VoIP Emergency Phones with 

Built-In Dialer and Digital Voice Announcer

The 

1600-IP Series

ADA Compliant VoIP Emergency Phones are designed

to provide quick and reliable handsfree communication for SIP VoIP phone
systems with PoE.  All 

1600-IP Series

phones meet ADA requirements for

elevator/ emergency telephones, and can be programmed from any Touch
Tone phone or PC on the same LAN. The phones can dial up to 5
programmable emergency numbers. In addition, the 

E-1600-20-IP, E-1600-

22-IP

E-1600-52-IP 

and 

E-1600-TP2IPEWP 

feature a second "

INFO

" button

that will dial up to 5 non-emergency numbers.

The 

1600-IP Series

phones can be programmed to automatically deliver a

digital announcement to identify the location of the emergency call.
Alternatively, a DTMF Touch Tone code may also be delivered.  A “Call
Connected” LED can be initiated manually or automatically.  All programming
parameters, including phone numbers and location numbers, are stored in
non-volatile memory, requiring no batteries.  All units are PoE powered.

For outdoor installations where the unit is exposed to precipitation or
condensation, select 

1600-IP Series

phones are available with Enhanced

Weather Protection (

EWP

).  EWP products feature foam rubber gaskets and

boots, sealed connections, gel-filled butt connectors, as well as urethane or
thermal plastic potted circuit boards. For more information, see

DOD 859

.

E-1600-IP            E-1600-45-IP         E-1600-60-IP        E-1600-65-IP

E-1600-20-IP        E-1600-22-IP

E-1600-30-IP         E-1600-32-IP

E-1600-50/52-IP

E-1600-53-IP

E-1600-55-IP           E-1600-03-IP

E-1600-02-IP/E-1600-TP-IPEWP

E-1600-TP2IPEWP/E-1600-GT-IPEWP

Summary of Contents for E-1600-ASTIPEWP
























Reviews: