14
E-1600-53-IP
Note:
This is a
E-1600-IP
board (PCB) only kit. This kit can be used to convert
2008 or newer Viking 1600A Series analog emergency phone to a VoIP version.
A special connector and microphone assembly is required to convert 2007 and
older Viking 1600A Series emergency phones. Contact Viking technicsal
Support if attempting to install this kit in these older phones. The kit can also be
used to replace a damaged “IP” board in the field.
(2) 0.156
diameter
type 2
mounting
holes
0.15
3.50
3.20
2.0
0.63
1.5
2.63
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
Connector and Wires from
Existing Standard (non EWP)
1600A Series Analog
Emergency Phone
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller,
SL-2
,
LV-1K
, etc.
3
1
10
1
Shipping Weight:
.45 kg (1 lb)
Connections:
(1) RJ45 10/100 Base-T, (3) optional gel-filled butt
connectors
Note:
When European CE compliance is required, mount in a metal
enclosure.
** Note:
These two red wires are
only used on units with an Info
button. When installing on a
single button unit, cut off these
two red wires and discard.
J3
MAC:
18E80FXXXXXX
asdesaxtff
J3
L9
C68
CR3
XTAL 2
TPG
Z1
1
Z9
CR4
CR1
C25
C37
c35
C5
L12
L1
1
L10
L8
R19
Z14
Z12
Z4
Z16
Z7
Z1
Z15
Z6
Z8
C59
R55
R58
L7
Z13
XT
AL4
XT
AL1
XT
AL3
C55
C71
C70
CR6
J1
Z3
C53
R20
R22
C22
C54
R63
R61
L13
R60
R59
R62
C72
C75
C73
Z10
Z2
Z5
L2
L1
C10
R16
C16
R25
R2
C21
R23
R24
RL1
C58
R18
C17
R39
R50
R54
R65
R11
R32
R12
R34
R53
J3J3J3J3
L
9
C68
C
R
3
XTAL 2
TP
G
Z
1
1
Z9
C
R4
C
R
1
C
C25
5
C37
7
c35
C5
L12
L
11
L1
0
L
8
R
1
9
Z
14
Z7
Z1
5
Z8
C59
R55
R58
L
Z13
XT
AL4
XT
AL1
XT
AL
3
C55
5
C71
C
7
0
C
C
R
6
J1
Z3
C53
3
R20
R22
C
2
2
C54
R
6
3
R61
L13
R60
Z1
Z
4
L7
Z
6
Z
1
2
R59
R62
C
7
2
C
7
5
C
7
3
Z
1
0
Z
2
Z5
L2
L1
C10
R
1
6
C16
6
R25
R2
C21
R23
R24
RL1
L
1
C58
R18
Z
1
6
C
1
7
R39
R50
R54
R65
R11
R32
R12
R34
R53
JJJ
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
- Black
+ Red
Black
Black
Red**
Red**
Yellow
Yellow
- Black
+ Red
LED
Help/Call Switch
Info Switch
(optional)
Speaker
Mic
FIGURE 1
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller,
SL-2
,
LV-1K
, etc.
E-1600-53-IP-EWP
Note:
This is a
E-1600-IP-EWP
board (PCB) only kit. This kit can be used to
convert any Viking 1600A-EWP Series analog emergency phone to a VoIP
version. The kit can also be used to replace a damaged “IP” board in the field.
Shipping Weight:
.45 kg (1 lb)
Connections:
(1) RJ45 10/100 Base-T, (13) gel-filled butt connectors
Note:
When European CE compliance is required, mount in a metal
enclosure.
Step 1.
Cut wires from J1 (10 pin connector) and J2 (3 pin connector).
Step 2.
Remove the two #6 phillips screws fastening the circuit board.
Step 3.
Cut off any stripped wire ends from the replacement cable.
Step 4.
Using the supplied gel-filled butt connectors, connect corre-
sponding wires from replacement cable to the previously cut
wires from the LED, Help/Call switch, optional Info switch,
Speaker and Microphone. See
FIGURE 1
for wire color and
polarity.
Replacing Analog 1600A Series EWP Potted Circuit Boards: