Viking Access Systems i-8 Installation Instructions And Safety Information Download Page 39

VIKING

standard features

and operator specifications

UL325  and  UL991  Listed  by  Underwriter  Laboratories  (UL)  •  Convenient  manual 
release • Standard Auto Open feature •  No limit switches necessary • Elegant design, 
appealing to any architectural project • Opening up to 110° • Operation speed of 
13 to 15 seconds per 90° • 100% duty cycle under very wide temperature range • 
400 cycles of operation on backup battery (500 lb. gate and 12

'

 length) • Intelligent 

speed  control  with  smooth  start  and  stop,  self-adjust  system  •  Modulated  speed 
regulator prevents exceeding operating speed that may reduce the service life of the 
gate  operator  and/or  installation  •  Intelligent  obstruction  detection  with  adjustable 
sensitivity • Overlap delay that holds one gate momentarily by an adjustable time 
while  the  other  gate  is  operating    (Master/Slave  installation  with  overlap  gates)  • 
Built-in  protection  against  lightning  strikes  or  similar  electrical  surges  •  Inherent 
overload  protection  in  the  regulated  power  supply  for  external  accessories  with 

multiple devices of protection

Viking Access Systems

Phone 800.908.0884 Fax 949.753.1640

631 Wald Irvine, CA 92618

www.vikingaccess.com

Summary of Contents for i-8








































Reviews: