background image

3

Adjustable wrench

Groove joint pliers
Plumber's putty
Pipe tape
Flat screwdriver

Your new faucet is designed for years of trouble-free performance.

Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or damage

the finish and/or product void your warranty.

If you use soldering for the installation of the faucet, the seats, cartridges

and washers will have to be removed before using flame. Otherwise,
warranty will be void on these parts

Protect your eyes with safety glasses when cutting or soldering water

supply lines
Cover your drain to avoid losing parts.

Prior to beginning installation, turn off the cold and hot water lines and open the hot
and cold knobs on the old faucet to release build-up pressure.

When installing your new faucet, turn the connector nuts finger-tight, then use one
wrench to anchor the fitting and a second wrench to tighten the nut one additional
turn. Connections that are too tight will reduce the integrity of the system.
Wrap all threaded connections with Teflon tape available at your local hardware or

plumbing supply store. Always wrap in a clockwise direction.

All installations can vary depending on how your previous faucet was installed. Not
all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.

Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all
parts are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.

1

4

2

2. CONNECT  FLEXIBLE

HOSES TO THE BRASS PIPES.

1. SHUT OFF WATER SUPPLY.
REMOVE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN

SINK SURFACE IN
PREPARATION FOR THE NEW
FAUCET. FLUSH WATER
CONNECTION AT HOME TO
MAKE SURE NO DEBRIS IS
STUCK IN THE LINE.

4. CONNECT FLEXIBLE

HOSES TO THE COLD AND
HOT WATER SUPPLY.

5. AFTER INSTALLATION IS
COMPLETE TURN ON THE
WATER SUPPLY VALVES AND
ALLOW BOTH HOT AND COLD
WATER TO RUN AT LEAST
ONE MINUTE EACH. WHILE
WATER IS RUNNING, CHECK

FOR LEAKS, ESPECIALLY AT
HOOK-UPS TO SUPPLY LINES.

TIGHTENING NUTS SLIGHTLY
WILL STOP ANY MINOR

LEAKS.

3. PLACE NEW FAUCET IN
THE POSITION ON THE SINK.
PLACE  BRASS RING
BETWEEN BOTTOM OF THE
FAUCET AND SINK SURFACE.
FROM UNDER THE SINK, PUT
RUBBER  WASHER AND
THREAD NUT ONTO THE PIN.
TIGHTEN NUT.

3

MAINTENANCE

REQUIRED TOOLS

IMPORTANT POINTS

SAFETY TIPS

INSTALLATION

ASSEMBLY

PACKAGE CONTENTS

Summary of Contents for VG01023






Reviews: