Viglen Vig560s Manual Download Page 12

Page: 12 / 86

Vig560s Motherboard Manual

System Board Components

Figure 2:

Motherboard Layout & Components

Table 1:

Motherboard Connections

A: Front Panel Audio Connector

O: Parallel IDE (P-ATA) connector

B: Realtek ALC861 audio codec

P: Power connector (24 way ATX2.2)

C: Aux/CD internal audio connector

Intel® 82801FB I/O Controller Hub (ICH6)

D: PCI Conventional bus add-in card connectors

R: Serial ATA (S-ATA) connectors

E: Intel Pro1000VE PCI Gigabit Ethernet Controller

S: Front panel connector

F: PCI Express x16 bus add-in card connector

T: 4 Mbit Firmware Hub (FWH)

G: Back panel connectors

U: Front panel USB connectors

H: +12V power connector (ATX12V)

V: Front panel USB connectors

I: LGA775 processor socket (Socket T)

W: Battery

J: Rear chassis fan connector

X: ITE 8211 controller (not fitted)

K: Processor fan connector

Y: Power to motherboard LED

L: DIMM Channel A & B Sockets

Z: Intel® 82915G Graphics Memory
Controller Hub (GMCH)

M: I/O controller

AA: PCI Express x1 bus add-in card

N: Floppy drive connector

BB: SPIDIF_OUT (not fitted)

Summary of Contents for Vig560s























































































Search results

Summary of Contents for Vig560s

Reviews:

Related manuals for Vig560s

Brands by name

Popular brands

Viglen Vig560s, Manual

Search results

Summary of Contents for Vig560s

Reviews:

Related manuals for Vig560s

Brands by name

Popular brands