background image

13

You can change any setting on your system centrally
at the control unit.

The control unit is equipped with a 

touchscreen

. To

input settings and check information, tap the on-screen
buttons.

Standby display

If the controls have not been operated for some time,
the display initially switches to the 

standby display

.

Fig. 1

After a few minutes, the illumination is switched off.

Status indicator

Depending on the type of heat generator, a red illumi-
nated strip (Lightguide) is displayed at the lower or
upper edge of the control unit during operation.

Meaning of the display:

Lightguide pulsates slowly:
Display is in standby mode.

Lightguide is illuminated constantly:
You are operating the control unit. Every input opera-
tion is confirmed by a brief flashing.

Lightguide flashes quickly:
There is a fault on the system.

Note

You can switch off the illuminated signal (light guide):
See page 19.

Home screen: Displays and settings

Call up the home screen as follows:

Standby display active:
Tap anywhere on the screen.

From the 

"Main menu"

:

Tap  .

Home screen displays

In the home screen, you can choose between the fol-
lowing displays:

Energy cockpit

Energy statement

In the delivered condition, the 

"Energy cockpit"

default display is always shown after switching on and
tapping  .
Use     to access the "Energy statement" display.

Operation

Operating principles

5839344

 

Summary of Contents for Vitovalor PA2













































Reviews: