background image

Safety instructions

2

Safety Instructions

Safety, Installation and Warranty Requirements

Please ensure that these instructions are read and understood before commencing installation and operation. Failure to comply with

the instructions listed below and details printed in these instructions can cause product/property damage, severe personal injury,

and/or loss of life. Ensure all requirements below are understood and fulfilled (including detailed information found in manual

subsections).

H

Licensed professional heating

contractor

The installation, adjustment, service,

and maintenance of this equipment

must be performed by a licensed

professional heating contractor.

"

Please see sections

entitled “Safety” and

“Important Regulatory and

Installation Requirements”.

H

Product documentation

Read all applicable documentation

before commencing installation. Store

documentation near boiler in a readily

accessible location for reference in the

future by service personnel.

"

For a listing of applicable

literature, please see

section entitled “Important

Regulatory and Installation

Requirements”.

H

Advice to owner

Once the installation work is complete,

the heating contractor must familiarize

the system operator/ultimate owner

with all equipment, as well as safety

precautions/requirements, shut-down

procedure, and the need for professional

service annually before the heating

season begins.

Warranty

Information contained in this and related

product documentation must be read

and followed. Failure to do so renders

warranty null and void.

Safety Terminology

The following terms could appear in these instructions to bring attention to the presence of potential hazards or important product

information. Please heed the advice given!

Helpful hints for installation, operation or

maintenance which pertain to the product.

51

67

50

5

51

67

50

5

Indicates an imminently hazardous

situation which, if not avoided, will

result in death, serious injury or

substantial product/property damage.

DANGER

Indicates an imminently hazardous

situation which, if not avoided, could

result in death, serious injury or

substantial product/property damage.

WARNING

Indicates an imminently hazardous

situation which, if not avoided, may

result in minor injury or product/property

damage.

CAUTION

IMPORTANT

Summary of Contents for Vitotrol 300

























Reviews: