manualshive.com logo in svg

Viessmann VITOFLEX 300-RF, Technical Manual, Page: 41 / 100

Share
Download
Viessmann VITOFLEX 300-RF Technical Manual Download Page 41

26

220x220

B

57

421

1048

228

820

638

410

250

320

215

A

A

Shut-off gate valve closed

B

Shut-off gate valve open

Drop chute L = 1.0 m

For part no., see pricelist

Connection of a drop section between the discharge system or con-
veyor device and an onward conveyor device by means of a drop
chute.

Note

The drop chute is 1 m long.
The design (diameter, profile) of the drop chute is matched to the rel-
evant project at the factory.

Special adaptor

For part no., see pricelist

Connection of a drop section between the external discharge system
and an onward conveyor device by means of a special adaptor.

Note

The design (diameter, profile) of the special adaptor is matched to
the relevant project at the factory.

Note

The existing on-site flange must be described (dimensions, hole pat-
tern) when ordering.

Installation accessories

 (cont.)

VITOFLEX 300-UF

Viesmann

41

5682428

4

 

Summary of Contents for VITOFLEX 300-RF





































































































Reviews:

No comments