Viessmann VIESMANN VITOLIGNO 300-H Page 25 Technical Manual Download | Manualshive

Page: 25 / 64

background image

Room temperature sensor

Part no. 7438 537

Separate room temperature sensor as supplement to the Vitotrol
300A; to be used if the Vitotrol 300A cannot be installed inside the main
living room or in a suitable position where the unit could capture and
adjust the temperature.
Installation in the main living room on an internal wall, opposite radia-
tors. Never install inside shelving units, in recesses, or immediately by
a door or heat source (e.g. direct sunlight, fireplace, TV set, etc.).
Connect the room temperature sensor to the Vitotrol 300A.
Connection:
■ 2-core lead with a cross-section of 1.5 mm

2

(copper)

■ Lead length from the remote control up to 30 m
■ Never route this lead immediately next to 230/400 V cables

20

80

□

Specification

Safety category

III

IP rating

IP 30 to EN 60529; ensure
through design/installation

Sensor type

Viessmann NTC 10 kΩ at
25 °C

Permissible ambient temperature
– Operation

0 to +40 °C

– Storage and transport

−20 to +65 °C

Temperature sensor

Immersion temperature sensor for DHW heating as a cylinder tem-
perature sensor (to plug 17 of the extension kit). The contact temper-
ature sensor, which is part of the standard delivery of the extension kit,
is used as a return temperature sensor (to plug 2 of the extension
kit).
The sensor well is not included in the standard delivery and must be
ordered separately.

Immersion temperature sensor

Part no. 7438 702

To capture the temperature in a sensor well.

Specification

Cable length

5.8 m, fully wired

IP rating

IP 32 to EN 60529; ensure
through design/installation

Sensor type

Viessmann NTC 10 kΩ, at
25 °C

Permissible ambient temperature
– Operation

0 to +90 °C

– Storage and transport

−20 to +70 °C

Note
Only for KM BUS mixer module

Stainless steel sensor well

Part no. 7819 693

SW24

200

R½

■ For on-site DHW cylinders
■ Part of the standard delivery of Viessmann DHW cylinders

Ecotronic control unit for Vitoligno 300-H

(cont.)

VITOLIGNO 300-H

VIESMANN

25

5672 507 GB

3

«
...
23
24
25
26
27
...
»

Summary of Contents for VIESMANN VITOLIGNO 300-H

































































Reviews:

No comments

Related manuals for VIESMANN VITOLIGNO 300-H

Altherma EHY2KOMB28AA

Brand: Daikin Pages: 44

HeatTransfer 399M

Brand: Munchkin Pages: 48

Brand: Instanta Pages: 8

Brand: Gabarron Pages: 44

ORLAN SUPER 130 kW

Brand: Orlanski Pages: 35

Brand: STIEBEL ELTRON Pages: 60

Brand: Effecta Pages: 43

Brand: Nibe Pages: 92

Brand: NTI Pages: 72

Aztec Classic WM Maxi Combi

Brand: Trianco Pages: 25

AAA Outdoor Boiler

Brand: Nature's Comfort Pages: 24

Brand: Nature's Comfort Pages: 25

Brand: Baxi Pages: 40

Brand: Baxi Pages: 48

System 100 HE Plus

Brand: Baxi Pages: 52

Brand: Rinnai Pages: 96

Brand: Logano Pages: 40

Brand: E.C.A. Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands