General
System requirements:
Surround sound:
PC sound card with 4-speaker 3D positional
sound capability, or PC-based or stand-alone surround
sound decoder.
Stereo sound:
Two-channel sound card or any line-level stereo
input device.
Cables supplied:
IEC mains cable, two 3.5 mm stereo jack to dual
RCA phono cables, and loudspeaker cables.
Approvals:
CE marked. Compliant with the EMC and Low Voltage
Directives (89/336/EEC and 73/23/EEC).
Dimensions:
Satellites:
100 mm (W) x 136 mm (H) x 74 mm (D)
Subwoofer
: 235 mm (W) x 420 mm (H) x 370 mm (D)
Amplifier:
204 mm (W) x 86 mm (H) x 340 mm (D)
Technical support:
Technical hotline and World Wide Web site.
Warranty:
Two years.
Loudspeakers
Subwoofer
MDF cabinet, containing magnetically shielded bass drive unit.
Low frequency drive unit:
Audax 6.5" cone (35 Hz to 130 Hz).
Satellites
Mid-frequency (bass/mid) drive unit and separate high-frequency
drive unit (tweeter), both magnetically shielded.
Bass/mid frequency drive unit:
Audax 3" cone.
High frequency drive unit:
Audax 10 mm polymer dome.
Amplifier
Self Peak Instantaneous Temperature (°Ke) (SPiKe™) Protection
Circuitry for protection against overvoltage, undervoltage,
overloads, including shorts to the supplies, thermal runaway,
and instantaneous temperature peaks.
Power supply unit:
Dual rail toroidal transformer with 28000 µF
of smoothing capacitance.
Power output:
80 watts RMS at 1% THD.
Frequency response:
< 3 Hz to >100 kHz.
THD (nominal output):
Less than 0.01% at 1 kHz.
Input sensitivity:
Inputs 1 & 3:
200 mVrms
Input 2:
1.5 Vrms
Controls:
Power on/off, Volume, Subwoofer volume (relative to
main volume), Front/rear fade, Source switch, Quad switch for
stereo surround.
Connectors:
Gold plated phono inputs for surround source, stereo
source, and Dolby Digital LFE channel; 3.5 mm jack for second
stereo source; individual outputs to each speaker unit; 3.5 mm
headphone jack on amplifier front panel; IEC mains inlet.
Internal Power Supply:
UK/Europe:
220-240V AC 50 Hz
North America:
115V AC 60 Hz
Technical specifications
Volume
increases or decreases
the volume produced by Sirocco
Crossfire.
Sub
increases or decreases
the volume produced by the
subwoofer.
Fade
balances the sound between the
front and rear speakers. Turn it anti-
clockwise to fade to the rear, clockwise
to fade to the front.
Source
selects which source you want to use.
•
If you’re using a PC for 3D positional gaming, or a surround sound decoder for home
cinema, select source 1.
•
If you’re using a full-size unit, such as a CD player, select source 2.
•
If you’re using a line-level device that has a 3.5mm jack output, such as a portable CD
or MiniDisc player, select Source 3.
This is where you plug in
your
headphones
.
When
you insert the
headphone jack, the
speakers are muted. Note
that, if you are using
headphones, you should
set the 3D positional
sound algorithm on your
sound card for
headphones.
For the stereo sources (2 and 3), the
Quad
switch duplicates the signal from the front
speakers to the rear speakers, so that you
can hear stereo surround through two sets
of stereo speakers.
Source 3
is connected via the socket at the front of the
amplifier. Use this for any line-level device that uses a
3.5mm jack, such as a portable CD or MiniDisc player.
Using the amplifier