background image

22

Maintenance Chart

Refer to the following table for routine maintenance.

Features

Requirements

Before use

After finish

Refuelling

Monthly

Yearly

If damaged

As required

Whole unit

Visual inspection (leaks)

Throttle lever

Check operation

Throttle trigger interlock

Check

Stop switch

Check

Fuel tank

Clean

Blower housing/impeller 
cover

Check & clean

Vac bag    

Clean

Replace

Air filter

Check

Clean

Replace (Depending on conditions)

Cowling

Clean

Cylinder fins

Clean

Spark plug

Clean & re-adjust gap

All accessible fasteners

Retighten

Muffler

Inspect

Inspect spark arresting screen

Clean or replace

Always stop the engine before any maintenance is done on the unit. 
When all parts have stopped rotating, disconnect the spark plug lead 
to begin maintenance work.

Never attempt maintenance that is not outlined in this manual. All 
repair work must be carried out by a Authorised Service Centre.

Before performing any maintenance ensure product is switched 
off & has come to a complete stop.

LR02390A-A.indd   23

22/07/2014   4:37:51 PM

Not for  

Reproduction

Summary of Contents for VPLV0226

































Reviews: