Vicon VC2650-DSP Installation And Operation Manual Download Page 17

Page: 17 / 86

Chapter 1 The

Overview

Camera control terminal

The terminal is used for camera control at the factory.

Vertical phase controller

Select “line” from the “V-SYNC” main menu in the “Setup” menus. It is

used for adjusting the vertical synchronization phase.

Power supply LED indication

Indicates that the power supply is on and functioning normally.

Power terminal

Connects the power adapter cable to the unit.

Lens cable input terminal

Connects the remote lens controller to the unit.

Video output terminal

Connects the video input terminal to the monitor. This connection allows

the video images to transmit from camera to monitor.

Camera operation switches

These switches’ function vary depending on the selection of two modes

on the

The general Operation Mode (the Setup menus are

not shown on the screen) and the Setup Menu Mode. The different mode

functions are shown below:

Summary of Contents for VC2650-DSP























































































Search results

Summary of Contents for VC2650-DSP

Reviews:

Brands by name

Popular brands

Vicon VC2650-DSP, Installation And Operation Manual

Search results

Summary of Contents for VC2650-DSP

Reviews:

Brands by name

Popular brands