Vicon V9360W Installation Manual Download Page 3

 
 

V9360W Hemispheric Camera with Advanced WDR 

Hardware User’s Manual 

 

Precautions 

Read these instructions 

Read all the safety and operating instructions before using this product.   

 

Heed all warnings 

Adhere to all the warnings on the product and in the instruction manual. Failure to follow the 

safety instruction given may directly endanger people, cause damage to the system or to other 

equipment.   

 

Servicing   

Do not attempt to service this video device yourself as opening or removing covers may 

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service 

personnel.

 

 

Trademarks 

All names used in this manual are probably registered trademarks of respective companies.   

 

Liability 

Every reasonable care has been taken during the writing of this manual. Inform your local 

office if you find any inaccuracies or omissions. We cannot be held responsible for any 

typographical or technical errors and reserve the right to make changes to the product and 

manuals without prior notice.   

 

FCC/CE Regulation 

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a commercial 

environment. This equipment generates, uses, and can radiate radio frequency energy and, if 

not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is likely 

to cause harmful interference in which case the users will be required to correct the 

interference at their own expense. 

         

Summary of Contents for V9360W




















Reviews: