Viatron AA800EZe, User Manual

Page: 8 / 36

8
AA800EZe rev.03
AA800EZe
2.4. Acknowledging an
Alarm
The Agri-Alert knows an alarm message has
been received when a user acknowledges the
alarm. There are several ways of doing this. If
you are on-site when an alarm is detected, en-
ter your password (if the password feature is
enabled) or simply press <1> key on the front
panel to acknowledge the alarm. You can also
acknowledge an alarm over the phone when
the Agri-Alert system reports the alarm or
you can call the Agri-Alert system yourself
between phone dialouts if the intercall time
is greater than zero (see section 2.5).
Follow this sequence to acknowledge an
alarm from the keyboard:
If this screen is not already displayed, 1.
press the
Alarm Memory button.
System is in alarm
Curtain doesn't move
Press 1 to continue
to acknowledge alarm
Continue
Press 1 to continue. 2.
If you have not been identified by the 3.
system yet, the Agri-Alert may prompt for a
password. Type in your password and then
press Enter.
Active Alarm Status
Alarm Memory
System is in Alarm
Press 1 to Acknowledge
Continue
View
Memory
Press 4. “#” to get details about the active
alarm situation or type 1 to acknowledge it
right away. Note that the dialout sequence
automatically starts when an alarm is set
off (if the zone in alarm uses the dialout
function).
The siren stops ringing when the alarm is
acknowledged. If the alarm is not acknowl-
edged at the end of the dialout sequence, the
Agri-Alert automatically acknowledges it and
stops the siren.
Telephone Interface 2.5.
The Agri-Alert system sends alarm reports
over the phone. You can also call the system
to get some status reports. When calling the
Agri-Alert, make sure the
“Phone Call-in”
pa-
rameters are set properly (see section 4.7).
2.5.1. Alarm Report Call
When an alarm occurs, the Agri-Alert system
tries to reach you by phone and dials all num-
bers of the dialout sequence (see chapter 4).
It puts an end to the dialout sequence when
the alarm is acknowledged.
The following section outlines the dialog ses-
sion when a number is reached. Note that a
touch-tone phone is required to respond to
the system prompts and that the system
automatically hangs up when the session
is over.
2.5.2. Status Report over the
Phone
You can dial into the Agri-Alert system and
obtain status reports over the phone. A
touch-tone phone is needed to respond to
the system prompts.
The following section outlines the dialogue
session when the Agri-Alert system answers
the call. The system automatically hangs up
when the status report is finished.
Telephone Session –
Alarm Call
Hello, this is Agri-Alert
ID message of the Agri-Alert
system
(if applicable)
Description of the alarm condi-
tion
(e.g.: “Alarm Zone 1”).
On-site Listening
[Microphone input is sent over
the phone for on-site listening
if enabled].
To acknowledge the alarm mes-
sage, enter your password and
press Star (*)
The user enters a four-digit pass-
word on the phone keypad and
presses start (*). If an incorrect
password is entered, the system
replies
“Wrong password”
; if it
is correct, the system replies
“OK”
. The system automatically
acknowledges the alarm when a
correct password is entered.
Main Menu:
- For a complete status report,
press 1;
- For a status report on a particu-
lar zone, press 2;
- To select relay, press 3;
- For on-site listening, press 4;
- To activate/bypass a zone,
press 5;
- For a new selection, press 8;
- To hang-up, press 0.
The user selects the desired
menu on the keyboard.