VIASYS Bear Cub 750PSV Service Manual Download Page 38 | Manualshive

Page: 38 / 98

VIASYS Bear Cub 750PSV Service Manual Download Page 38

38

Bear

Cub

750PSV

NOTE

If problems are incurred in obtaining the calibration performance, refer to
Troubleshooting (

Chapter

6) or contact your dealer or VIASYS Healthcare Service

Facility.

Pressure Transducers and Flow Control Valve
Calibration

Turn OFF the ventilator and disconnect tubing to the Pressure Transducers on the
Control PCB. Press and hold the diagnostic switch on the Control PCB while turning
the ventilator ON to enter Transducers and Flow Calibration routines. Throughout
calibration, the TEST key is for advancing the calibration number; VISUAL RESET is
for backing to previous calibration, and the MANUAL BREATH key is for recording
calibration data. The calibration number and message are displayed in the Breath
Rate and Monitored Time/I:E Ratio windows respectively. Data (when applicable) is
displayed in the Monitored Pressure window. Refer to the following (See table 4-1)
to calibrate the transducers on the Control PCB:

Table 4-1: Control PCB Transducer Calibration

Transducer

Calibration Number

Message

Input Static Pressure

Machine (port B)

d00

nP00

0 cmH2O

d01

nP40

40 ± 0.2 cmH2O

Differential (port B)

d02

dP00

0 cmH2O

d03

dP40

40 ± 0.2 cmH2O

Proximal (port B)

d04

pP00

0 cmH2O

d05

pP40

40 ± 0.2 cmH2O

O2 (A2)

d06

0P00

0 PSIG

d07

0P40

40 ± 0.2 PSIG

AIR (A1)

d08

AP00

0 PSIG

d09

AP40

40 ± 0.2 PSIG

NOTE

The 40 cm/psi settings were 70 cm/psi prior to monitor firmware 511-02803-00.
When calibrating the pressure transducers, both pressure points (i.e. 0 and 40
cm/psi) must be read and the 0 cm/psi reading must be obtained first.

1.

Check the accuracy of the five pressure transducers per table 4.2. The
window shows the pressure readings monitor pressure.

2.

Press the TEST key to advance the calibration number to the Display Set
Altitude Test, then press the MANUAL BREATH key until the number in the
PRESSURE window indicates the altitude at which the Flow Control valve
calibration is to be performed (expressed in units of 100 ft). Then advance to
the next test number and power down.

3.

Re-connect tubing to the transducers on the Control PCB; apply Air and O2
(approximately 50 psi) to UUT. Use an RT-200 to measure flow at the TO

L2346

Revision B

June 2004

«
...
36
37
38
39
40
...
»

Summary of Contents for Bear Cub 750PSV



































































































Reviews:

No comments