manualshive.com logo in svg

Vextrec GMB-486SPS, User Manual, Page: 58 / 61

Share
Download
Vextrec GMB-486SPS User Manual Download Page 58

BIOS POST Message

53

RAM PARITY ERROR messages when the segment that has caused the problem has been isolated.

PRESS A KEY TO REBOOT:
This will be displayed at the bottom screen when an error occurs that required you to reboot.  Press any key
and the system will reboot.

PRESS F1 TO DISABLE NMI, F2 TO REBOOT:
When BIOS detects a Non-markable Interrupt condition during boot, this will allow you to disable the NMI
and continue to boot, or you can reboot the system with the NMI enabled.

RAM PARITY ERROR - CHECKING FOR SEGMENT ...:
Indicates a parity error in Random Access Memory.

Should Be Empty But EISA Board Found
PLEASE RUN EISA CONFIGURATION UTILITY:
A valid board ID was found in a slot that was configured as having no boards ID.

*** NOTE:

When this error appears, the system will boot in ISA mode, which allows you to run the
EISA Configuration Utility.

Should Have EISA Board But Not Found
PLEASE RUN EISA CONFIGURATION UTILITY:
The board installed is not responding to the ID request, or no board ID has been found in the indicated slot.

*** NOTE:

When this error appears, the system will boot in ISA mode, which allows you to run the
EISA Configuration Utility.

Slot Not Empty:
Indicates that a slot designated as empty by the EISA Configuration Utility actually contains a board.

*** NOTE:

When this error appears, the system will boot in ISA mode, which allows you to run the
EISA Configuration Utility.

SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT ...:
Indicates the present boot attempt has been aborted and the system must be rebooted.  Press and hold down the
CTRL and ALT keys and press DEL.

Wrong Board In Slot
PLEASE RUN EISA CONFIGURATION UTILITY:
The board ID does not match the ID stored in the EISA non-volatile memory.

*** NOTE:

When this error appears, the system will boot in ISA mode, which allows you to run the
EISA Configuration Utility.

Summary of Contents for GMB-486SPS






























































Reviews:

No comments