background image

Table of Contents

 

 

Rev. 3/4/2019 

  POW-CAR-AR5 MANUAL 

Table of Contents

 

Copyright 2019 Vestil Manufacturing Corp.  

Page 1 of 13 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

POW-CAR-AR5 Powered Carousel with Approach Ramps 

Instruction Manual 

 

 

 

 

Receiving instructions: 

 

After delivery,  remove the packaging from the product. Inspect the product closely to determine 

whether it sustained damage during transport. If damage is discovered, record a complete description 

of it on the bill of lading. If the product is undamaged, discard the packaging.

 

 

NOTE:

 

The end-user is solely responsible for confirming that  product design, use, and maintenance 

comply with laws, regulations, codes, and mandatory standards applied where the product is used.

 

 

Replacement Parts and Technical Assistance:  

 

For answers to questions not addressed in these instructions and to order replacement parts, 

labels, and accessories, call our Technical Service and Parts Department at (260) 665-7586. The 

department can also be contacted online at 

http://www.vestilmfg.com/parts_info.htm

. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vestil Manufacturing Co. 

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 

Telephone: (260) 665-7586    Toll Free (800) 348-0868 

Fax: (260) 665-1339 

  

Web: 

www.vestilmfg.com

  

 

 

Table of Contents 

Specifications

…………….…………………………………..……………………………………………………………… 

2

 

Signal Words

….……………………………………………………………………………………………………… …….

2

  

Hazards

………………….……………………………………………………………………..…………………….. …….

3

 

Exploded View

 & 

Bill of Materials: POW-CAR-AR5

………...…………………………………..……………………

 4

 

Exploded View

 & 

Bill of Materials: Power Unit Subassembly

 ……………………………..………………………….. 

5

 

Exploded View & Bill of Materials: Thrust Bearing Subassembly

………………………………….………… ……. 

6

 

Electrical System Diagram

……………………………………………………………………………………….. …….

6

 

Delta Motor Speed Controller

…………………………………………………………………………………………… 

7

 

Installation and Assembly

…………………………………………………………………………………………………. 

8

 

Adjusting Chain Tension

 …………..

  

…………………………………………………………................................

        

9

 - 

10

 

Using the Carousel

………………………………………………………………………………………………………… 

10

 

Record of Normal Condition

……………………………………………………………………………………………… 

10

 

Inspections and Maintenance

………………………………………………………………………………………..

10

 - 

11

 

Troubleshooting

……………………………………………………………………………………………………………

11

 

Labeling Diagram

………..…...…………………………………………………………………………………………

12

 

Limited Warranty

…...……………………………………………………………………………………………………...

13

 

 

Summary of Contents for POW-CAR-AR5














Reviews: